UHPPOTE UT0511-622S

UHPPOTE Electric Strike Lock UT0511-622S Instruction Manual

Model: UT0511-622S

Sarrera

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of the UHPPOTE Electric Strike Lock, model UT0511-622S. This device is designed for use with European and American fire push bars in access control systems for double doors, fire exits, and emergency doors.

Ohar garrantzitsua: This electric strike lock requires a separate push panic bar for operation. Please refer to ASIN: B06XWY91HQ for compatible push panic bars.

Produktua amaituview

The UHPPOTE Electric Strike Lock (Model UT0511-622S) is constructed with a 304 Stainless Steel lock tongue, featuring a nickel-coated surface for durability. It is designed to integrate with existing access control systems and fire push bars.

UHPPOTE Electric Strike Lock, front view

1. irudia: Aurrealdea view of the UHPPOTE Electric Strike Lock.

UHPPOTE Electric Strike Lock, angled view

2. irudia: Angeludun view of the UHPPOTE Electric Strike Lock, showing the strike plate and mounting holes.

Zehaztapenak

Modelo zenbakiaUT0511-622S
MarkaUHPPOTE
Blokeo motaSarraila elektrikoa
MaterialaAltzairu herdoilgaitza
Akabera motaNickel-coated
Lock Tongue Structure304 altzairu herdoilgaitza
Euste-indarra1000 kg / 2204 lb
Seinale IrteeraDoor sensor NO/NC/COM
Neurriak (L x W x H)6.04 x 1.69 x 1.93 hazbete (153.5 x 43 x 49 mm)
Elementuaren pisua0.52 kilogramo
BateragarritasunaEuropean & American fire push bars
UPC701385688349
Detailed dimensions diagram of the electric strike lock

Figure 3: Detailed dimensions of the UHPPOTE Electric Strike Lock for precise installation planning.

Konfigurazioa eta Instalazioa

Proper installation is crucial for the reliable operation of the electric strike lock. Follow these steps carefully.

  1. Prestatu atearen markoa: Mark the drilling positions on the door frame according to the lock's dimensions. Ensure the location allows for proper alignment with the panic push bar.
  2. Cut the Lock Hole: Carefully cut a recess in the door frame for the lock body. This step requires precision to ensure the lock sits flush.
  3. Zulagailuak muntatzeko zuloak: Drill pilot holes for the mounting screws at the marked positions.
  4. Mount the Electric Strike: Insert the electric strike lock into the prepared recess and fasten it securely to the door frame using appropriate screws.
  5. Kableatua: Connect the electric strike lock to your access control system. The signal output provides door sensor status (NO/NC/COM).
    • Green: NO (Normally Open)
    • White: COM (Common)
    • Yellow: NC (Normally Closed)
    • Gorria: +12VDC
    • Black: - (Ground)
  6. Function Conversion (Fail-Safe/Fail-Secure): The lock can be configured for fail-safe (NO mode) or fail-secure (NC mode) operation.
    • Izan ere EZ modua (Fail-Safe - unlocks when power is lost): Unscrew the nut and adjust the security mode to the short end of the screw.
    • Izan ere NC modua (Fail-Secure - locks when power is lost): Unscrew the nut and adjust the security mode to the long end of the screw.
  7. Install Panic Push Bar: Install the compatible panic push bar on the door, ensuring it aligns correctly with the electric strike lock.
Installation diagram showing wiring and function conversion

Figure 4: Installation diagram illustrating signal output wiring and function conversion for NO/NC modes.

Diagram showing electric strike lock installed on a door frame with a panic bar

5. irudia: Adibample installation of the electric strike lock with a panic push bar on a double door.

Instalazio Bideo Gida

Video 1: A visual guide demonstrating the installation process for the UHPPOTE Electric Strike Lock with a panic push bar.

Funtzionamendu-argibideak

The electric strike lock operates in conjunction with an access control system and a panic push bar. When the access control system sends an unlock signal, the electric strike releases the door latch, allowing the door to be opened. In an emergency, pressing the panic push bar will mechanically release the door, regardless of the electric strike's state (if properly installed as a fire exit device).

The lock's operational mode (fail-safe or fail-secure) determines its behavior during a power outage:

  • Fail-Safe (NO mode): The lock will unlock automatically when power is removed. This is typically used for fire exits where egress must always be possible during a power failure.
  • Fail-Secure (NC mode): The lock will remain locked when power is removed. This is common for security applications where the door should remain secured during a power failure.

The integrated door sensor provides feedback to the access control system regarding the door's open or closed status.

Mantentzea

To ensure long-term reliability and performance of your UHPPOTE Electric Strike Lock, regular maintenance is recommended:

  • Garbiketa: Periodically clean the exterior of the strike lock with a soft, dry cloth. Avoid abrasive cleaners or solvents.
  • Ikuskapena: Annually inspect the lock tongue and strike plate for any signs of wear, damage, or obstruction. Ensure the lock tongue moves freely.
  • Loturaren egiaztapena: Verify that all mounting screws are tight and secure. Loose fasteners can affect the lock's alignment and operation.
  • Kableatuen egiaztapena: Inspect wiring connections for any signs of corrosion or damage. Ensure all connections are secure.

If any issues are observed, refer to the Troubleshooting section or contact customer support.

Arazoak konpontzea

If you encounter problems with your electric strike lock, consult the following common issues and solutions:

ArazoaKausa posibleaIrtenbidea
Lock does not secure properly (door can be opened even when locked).The internal pin that blocks the lock tongue may not be seating far enough.
  • Check the alignment of the strike lock with the panic bar's latch.
  • Inspect the internal mechanism for obstructions or damage.
  • Ensure the lock is correctly configured for fail-secure (NC) mode if intended to remain locked without power.
  • Arazoak jarraitzen badu, jarri harremanetan bezeroarentzako laguntza-zerbitzuarekin.
Lock does not unlock when signal is applied.No power, incorrect wiring, or faulty access control signal.
  • Verify power supply to the lock (12VDC).
  • Check all wiring connections according to the installation diagram.
  • Test the access control system's output signal.
  • Ensure the lock tongue is not jammed by excessive pressure from the door.
Door sensor status is incorrect.Incorrect wiring of the door sensor output.
  • Re-check the Green (NO), White (COM), and Yellow (NC) wire connections to your access control panel.
  • Ensure the door sensor mechanism within the strike is not obstructed.

Bermearen informazioa

Specific warranty details for the UHPPOTE Electric Strike Lock (Model UT0511-622S) are not provided in this manual. Please refer to the product packaging, the official UHPPOTE website, or contact UHPPOTE customer support directly for current warranty terms and conditions.

Bezeroarentzako Arreta

For further assistance, technical support, or inquiries regarding your UHPPOTE Electric Strike Lock, please contact UHPPOTE customer service or visit their official store.

© 2024 UHPPOTE. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.