iFixit Battery Replacement Kit for iPad Air, iPad 5, and iPad 6 (Model A1484)

Sarrera

This manual provides detailed instructions for replacing the battery in your iPad Air (1st Generation), iPad 5, or iPad 6 using the iFixit Battery Replacement Kit. Please read all instructions carefully before beginning the repair process. This kit is designed to provide the necessary components and tools for a successful battery replacement.

Segurtasun Informazioa

• Itzali beti gailua erabat konponketa bat hasi aurretik.
• Disconnect the battery connector before performing any other repairs to prevent accidental short circuits.
• Lithium-ion batteries can be hazardous if punctured or damaged. Handle with care.
• Use appropriate tools and follow instructions to avoid damaging your device or injuring yourself.
• Bota ezazu bateria zaharrak arduraz tokiko araudiaren arabera.

Kitaren edukia

The iFixit Battery Replacement Kit includes the following components:

• Replacement Battery (Model A1484 compatible)
• iOpener heating pad
• Precision screwdriver with various bits
• Bentosa
• Opening picks
• Spudger
• Pintzak
• Adhesive strips for battery and screen reassembly

Image: Contents of the iFixit Battery Replacement Fix Kit, including the battery, iOpener, screwdriver, suction cup, opening picks, spudger, tweezers, and adhesive strips.

Konfigurazioa eta Prestaketa

1. Gather Your Workspace: Ensure you have a clean, well-lit, and organized workspace. Use a magnetic mat or parts organizer to keep track of small screws and components.
2. Itzali gailua: Completely power off your iPad. Hold the power button and slide to power off.
3. Charge iOpener: Heat the iOpener in a microwave according to its instructions (typically 30 seconds). The iOpener is used to soften the adhesive holding the screen in place.
4. Datuen babeskopia: It is recommended to back up your iPad's data before starting any repair.

Operating Instructions: Battery Replacement Procedure

This section outlines the general steps for replacing the battery. For detailed, step-by-step visual guides, refer to the official iFixit repair guides available on their website. The process involves carefully separating the screen, disconnecting the old battery, removing it, installing the new battery, and reassembling the device.

1. Screen Removal:
   • Apply the heated iOpener to the edges of the iPad screen to soften the adhesive.
   • Use the suction cup to create a gap between the screen and the frame.
   • Carefully insert opening picks into the gap and slide them around the perimeter to separate the adhesive. Exercise caution to avoid damaging internal components, especially cables.
   • Once the adhesive is sufficiently loosened, gently open the screen, being mindful of the display and digitizer cables connecting it to the logic board. Do not fully detach the screen yet.
2. Deskonektatu bateria:
   • Locate the battery connector on the logic board.
   • Use a plastic spudger to carefully pry up and disconnect the battery connector. This is a critical step to prevent short circuits during the repair.
3. Kendu bateria zaharra:
   • The battery is typically secured with strong adhesive. Apply heat again to the back of the iPad in the area of the battery to soften the adhesive.
   • Use a plastic card or spudger to carefully pry the old battery out. Avoid bending or puncturing the battery.
4. Instalatu bateria berria:
   • Clean any remaining adhesive residue from the battery compartment.
   • Apply the new adhesive strips provided in the kit to the back of the new battery or the iPad frame, as instructed by the specific guide for your iPad model.
   • Carefully place the new battery into position, ensuring it aligns correctly.
   • Reconnect the new battery's connector to the logic board.
5. Berriz muntatzea:
   • Reconnect any other cables that were disconnected during the screen removal process.
   • Apply new adhesive to the screen frame if necessary (some kits include this).
   • Carefully close the screen, ensuring all clips and connections are secure.
   • Apply gentle pressure around the edges of the screen to secure the new adhesive.
6. Hasierako piztea:
   • Power on your iPad and test its functionality, including touch screen response and charging.
   • It is recommended to fully charge the new battery and then allow it to discharge completely for calibration.

Image: Close-up of the iFixit screwdriver handle, showing an integrated SIM eject tool, useful for removing SIM card trays before opening the device.

Image: The iFixit replacement battery, showing its specifications and connectors, ready for installation.

Mantentzea

To ensure the longevity and optimal performance of your new battery:

• Avoid extreme temperatures (both hot and cold) as they can degrade battery health.
• Do not allow the battery to fully discharge frequently. Charge your device before it reaches critically low levels.
• Use certified charging accessories to prevent damage to the battery and device.
• If the device will be stored for an extended period, charge the battery to approximately 50% before storage.

Arazoak konpontzea

Zehaztapenak

• Bateriaren zelulen konposizioa: Litio ioia
• Berrerabilgarritasuna: Birkargagarria
• Eredu bateragarriak: iPad Air (1st Generation), iPad 5, iPad 6
• iFixit Model Number: A1484 (for battery compatibility)
• Elementuaren pisua: Approximately 1.81 pounds (entire kit)
• Fabrikatzailea: iFixit

Bermea eta Laguntza

iFixit products are known for their quality and are often backed by a warranty. For specific warranty details regarding your battery replacement kit, please refer to the official iFixit website or contact their customer support directly. iFixit also provides extensive online repair guides and community forums for additional assistance.

• Official iFixit Webgunea: www.ifixit.com
• Repair Guides: iFixit iPad Repair Guides
• Bezeroarentzako laguntza: Refer to the iFixit webharremanetarako informazioa lortzeko gunea.