Enbrighten Z-Wave Plus In-Wall Smart Fan Control

Sarrera

Thank you for choosing the Enbrighten Z-Wave Plus In-Wall Smart Fan Control. This device allows you to wirelessly control and adjust the speed of your ceiling fan from anywhere when paired with a compatible Z-Wave hub. It offers convenient automation possibilities for your home, integrating seamlessly with various smart home systems.

Image: The Enbrighten Z-Wave Plus In-Wall Smart Fan Control, highlighting its features and compatibility.

Segurtasun Informazioa

Read all instructions before installation and use. Adhere to all national and local electrical codes. If you are unsure about any part of these instructions, consult a qualified electrician.

• SHOCK ARRISKUA: Disconnect power at the circuit breaker or fuse box before installation.
• SUTE ARRISKUA: Ez gainditu 2.5eko gehienezko karga-balorazioa Amps for the fan.
• This device is designed for use with permanent ceiling fans only. Do not use with exhaust fans, fans with remote controls, or fans with built-in speed controls.
• Ensure proper grounding. A neutral wire is required for operation.
• Instalatu barrualdean bakarrik.

Paketearen edukia

• 1 x Enbrighten Z-Wave Plus In-Wall Smart Fan Control
• 1 x White Paddle (pre-installed)
• 1 x Light Almond Paddle
• Argibide eskuliburua

Produktua amaituview eta Ezaugarriak

The Enbrighten Z-Wave Plus Fan Control is designed to provide smart control over your ceiling fan.

• Haririk gabeko kontrola: Remotely turn on/off and adjust fan speeds (High, Medium, Low).
• Z-Wave Plus Ziurtagiria: Ensures broad compatibility with Z-Wave hubs and devices.
• Irisgarritasun-luzatzailea: Repeats Z-Wave signals to extend network range up to 150ft.
• Changeable Paddles: Includes white and light almond paddles to match your decor.
• 3-Way Compatible: Can be used in single-pole or 3-way installations (requires additional switch, sold separately).

Image: Visual representation of the smart fan control's capabilities, including scene customization, remote control, scheduling, and device compatibility.

Image: The included white and light almond paddles, demonstrating their interchangeability to match different interior designs.

Instalazioa

Kableatu-diagrama

Before beginning, ensure power is OFF at the circuit breaker. This device requires a neutral wire.

Image: Detailed wiring diagram illustrating how to connect the fan control to your home's electrical system, including ground, load, traveler, line, and neutral connections.

Urratsez urratseko instalazioa

1. Itzali energia: Locate the circuit breaker controlling the fan and turn it OFF. Verify power is off by toggling the existing fan switch.
2. Kendu etengailu zaharra: Unscrew and carefully pull the existing switch from the wall box. Disconnect all wires from the old switch.
3. Identifikatu kableak:
   • Line (Hot): Normalean beltza, zirkuitu-hausletik datorrena.
   • Karga: Usually black, going to the fan.
   • Neutroa: Usually white, often bundled in the back of the box. (REQUIRED)
   • Lurzorua: Normalean berdea edo kobre biluzik.
   • Traveler (for 3-way): Only present in 3-way installations.
4. Konektatu kableak:
   • Connect the green or bare copper ground wire from the wall box to the fan control's GREEN terminal.
   • Connect the Line (hot) wire to one of the fan control's BLACK terminals (labeled "LINE").
   • Connect the Load wire (to fan) to the other BLACK terminal (labeled "LOAD").
   • Connect the Neutral wire from the wall box to the fan control's SILVER terminal (labeled "NEUTRAL").
   • If installing in a 3-way setup, connect the Traveler wire to the fan control's YELLOW/RED terminal (labeled "TRAVELER"). Cap any unused traveler wires.
5. Muntaketa-etengailua: Carefully push the wired fan control into the wall box. Secure it with the provided screws.
6. Attach Wallplate: Install the wallplate (sold separately).
7. Berrezarri boterea: Piztu berriro korrontea etengailu elektrikoan.

Funtzionamendu-argibideak

Eskuzko Kontrola

• ON/OFF: Press the top or bottom of the rocker switch to turn the fan ON or OFF.
• Abiadura doitzea: Press the small button below the rocker switch repeatedly to cycle through fan speeds: Low, Medium, High, Off.

Z-Wave Pairing (Inclusion)

To add the fan control to your Z-Wave network, follow these steps:

1. Place your Z-Wave controller into inclusion (pairing) mode. (Refer to your Z-Wave hub's manual for specific instructions).
2. Press the top or bottom of the fan control's rocker switch once. The LED indicator will flash to confirm inclusion mode.
3. The fan control will automatically be added to your network. The LED will stop flashing once successfully paired.
4. You can now control the fan speed and ON/OFF status through your Z-Wave hub's interface or connected voice assistants (e.g., Alexa, Google Assistant).

Z-Wave Unpairing (Exclusion)

To remove the fan control from your Z-Wave network:

1. Place your Z-Wave controller into exclusion (unpairing) mode.
2. Press the top or bottom of the fan control's rocker switch once. The LED indicator will flash to confirm exclusion mode.
3. The fan control will be removed from your network. The LED will stop flashing once successfully unpaired.

Image: The smart fan control enables wireless control and scheduling of ceiling fans in both indoor and outdoor settings.

Mantentzea

The Enbrighten Z-Wave Plus Fan Control requires minimal maintenance.

• Garbitu gainazala leun batekin, damp oihal. Ez erabili garbitzaile edo disolbatzaile urratzailerik.
• Ziurtatu gailua ez dagoela hezetasun gehiegi edo tenperatura altuen eraginpean.

Arazoak konpontzea

Zehaztapenak

Image: Dimensional drawing of the fan control, providing precise measurements for installation planning.

Bermea eta Laguntza

Enbrighten products are backed by a limited-lifetime warranty. For warranty details, technical support, or to register your product, please visit the official Enbrighten webwebgunean edo jarri harremanetan bezeroarentzako zerbitzuarekin.

• Fabrikatzailea: Jasco Products Company, LLC
• Webgunea: byjasco.com (General Jasco site, Enbrighten is a brand under Jasco)
• Laguntza-harremana: Kontsultatu fabrikatzailearen webgunea kontaktu-informazio eguneratuena lortzeko.