KMC CONTROLS STE-9000 series NetSensor Damage from Incorrect
Zehaztapenak
- Product: STE-9000 series NetSensor
- Features: Temperature and humidity readings
- Model: All STE-9000 series NetSensors
Produktuak erabiltzeko jarraibideak
- Ensure that both tabs on the sensor cover rest on top of the backplate.
- Make sure the anti-tamper hex screw is fully rotated into the backplate before installing or uninstalling the sensor cover.
- Swing the cover from the top onto the backplate.
- Do NOT push the cover directly onto the plate or swing it from the bottom.
- If any force seems to be needed, check the alignment of the tabs on the top of the backplate and/or the anti-tamper screw before swinging the sensor cover onto the backplate.
- For more detailed installation instructions, please refer to the STE-9000 Series NetSensors Installation Guide.
Bete urrats hauek KMC Conquest STE-9000 Series Digital NetSensor muntatzeko eta konektatu Conquest BAC-59xx/9xxx Kontrolagailu batera.
OHARRA: Ikusi Conquest NetSensors STE- 9000 Series Digital Room Sensors fitxa teknikoa eta Konkista aukeratzeko gida at kmccontrols.com for specifications and other information.
OHARRA
- BEHATU GAILU ELEKTROSSTATIKOEN SENTSIBLEAK MANIPULATZEKO NEURRIK
HAUTATU MUNTATZEKO KOKAPENA
- Ikusi Gela-sentsorea eta termostatoa muntatzeko kokapena eta mantentze-aplikazioen gida for cautions, troubleshooting, and best practices.
OHARRA: Osatu kableatuak toki bakoitzean sentsore bat instalatu aurretik.
KENDU ATZEKO PLAKA
- Turn the hex screw(1) clockwise into the sensor until the screw clears the cover.
OHARRA: The hex screw(2_ should remain in the backplate.
- Atera estalkia atzeko plakatik.
KONEKTATU ETHERNET KABLEA - Feed the Ethernet patch cable(3) from the Conquest controller through the center of the backplate(4).
OHARRA: Ethernet adabaki-kableak gehienez 150 oin (45 metro) izan behar du.
- Muntatu atzeko plaka kaxa elektriko batean emandako torlojuak erabiliz.
OHARRA: If additional thermal insulation is needed, install the optional HPO-9002 gasket before installing the backplate.
Informazio gehiagorako, ikusi Room Sensor and Thermostat Mou
nting Location and Maintenance Application Guide. - Entxufatu Ethernet kablea 5 sentsorearen 6 modular-konektorean.
INSTALATU SENTSOREEN ESTALDIA - Place the cover(7) over the top of the backplate(8) and swing it down.
OHARRA: Kontuz Ethernet kablea ez atxilotzeko.
- Turn the hex screw(9) counterclockwise until it engages the cover.
ERAGIN
- The STE-9000 Series NetSensor becomes operational after it is connected to a powered Conquest controller.
- OHARRA: To change setpoints or configuration, see the KMC Conquest Controller aplikazioen gida.
- OHARRA: For continued maximum NetSensor efficiency, see the maintenance section in the Gela-sentsorea eta termostatoa muntatzeko kokapena eta mantentze-aplikazioen gida.
OHAR GARRANTZITSUAK
- Dokumentu honetako materiala informaziorako soilik da. Edukiak eta deskribatzen dituen produktuak abisurik gabe alda daitezke.
- KMC Controls, Inc. makes no representations orwarranties with respect to this document. In no event shall KMC Controls, Inc. be liable for any damages, direct, or indirect, arising out of or related to the use of this document.
- KMC logotipoa KMC Controls, Inc-ren marka erregistratua da. Eskubide guztiak erreserbatuta.
KONTAKTU
- TELEFONOA: 574.831.5250
- FAXA: 574.831.5252
- e-posta: info@kmccontrols.com
Ohiko galderak
Q: Which models are affected by the installation issue?
A: This issue affects all STE 9000 series NetSensors.
Q: What are the potential errors from a damaged printed circuit board?
A: Incorrect temperature and humidity readings may result from a damaged printed circuit board.
Dokumentuak / Baliabideak
 |
KMC CONTROLS STE-9000 series NetSensor Damage from Incorrect Installation [pdfErabiltzailearen gida STE-9000 series NetSensor Damage from Incorrect Installation, STE-9000 series, NetSensor Damage from Incorrect Installation, NetSensor Damage from Incorrect Installation, NetSensor Damage, from Incorrect Installation |