MOULTRIE MFG-15050 Ranch Series Gravity Feeder Kit Argibideak

MOULTRIE MFG-15050 Ranch Series Gravity Feeder Kit Argibideak

TRESNAK

• Bolt  M6 x 1 x 18 Qty.
  
• Hex Nut M6 x 1 Qty. 9
  
• Flat Washer M6 Qty. 6
  

ASSEMBLE FEEDER KIT

1. Kendu hardware guztia ontzitik.
   
2. From the inside of your feeder hopper, install (3) M6 bolts, fitted with washers, through the mounting bolt holes on the bottom. Do not thread anything onto the bolts at this time, this will be the mounting hardware for the gravity kit.
   
3. Fit the Extension Tube to the top of the gravity head, aligning the 3 bolt holes.
   
4. From the outside of the extension tube, Insert the (3) M6 bolts through the holes from Step 3. Secure with the supplied hex nuts on the inside of the tube. Once all three bolts are in place and hex nuts are finger tight, fully tighten with 10mm wrench.
   ONLY TIGHTEN AFTER ALL 3 BOLTS ARE INSTALLED (10mm wrench)
   
5. Following the same procedure from Step 4, attach the Mounting Plate (ribs facing downward) to the top of the Extension Tube.
   ONLY TIGHTEN AFTER ALL 3 BOLTS ARE INSTALLED (10mm wrench)
   
6. The kit is now ready to be installed to your hopper. Align the pre-installed mounting studs from Step 2 with the (3) holes in the mounting plate, then secure the kit using (3) Flat Washers and (3) Hex Nuts.
   ONLY TIGHTEN AFTER ALL 3 BOLTS ARE INSTALLED (10mm wrench)
   
   

TRESNAK

• Short M6 Bolt M6 x 1 x 14 Qty. 20
  
• M6 Lock Nut M6 x 1 Qty. 20
  
• Short M8 Bolt M8 x 1.25 x 14 Qty. 8
  
• M8 Lock Nut M8 x 1.25 Qty. 16
  
• Long M8 Bolt M8 x 1.25 x 60 Qty. 8
  

MUNTATU TOLLA

1. Kendu hardware guztia ontzitik.
   
2. Bildu 4 hopper panelak eta hopper konoa.
   

Place the cone on its side, with the front arrow pointing upwards. Attach both side panels to the cone using (6) Short M6 Bolts and (6) M6 Lock Nuts. Hand tighten only.

Jarri aurpegiko panel bat konoaren gainean eta alboko panelak gainjarriz. Lerrokatu konoko torloju-zuloak aurpegiko paneleko (3) beheko zuloekin. Seguru (3) M6 Torloju laburrak eta (3) M6 blokeo azkoinak erabiliz. Eskuz estutu bakarrik.

Irauli hoppera eta instalatu gainerako aurpegiko panela goiko prozedura bera jarraituz.

OPTIONAL

Stand the hopper upright with the cone flat on the floor. Align the bolt holes in the top (4) corners. Secure with (4) Short M6 Bolts and (4) M6 Lock Nuts. Hand tighten only

Jarri (4) leg brackets against the corner bracket mounting holes as shown, align the holes and insert (2) short M8 bolts from the outside of each leg bracket into the hopper. Secure with a hand-tight M8 lock nut on each bolt (8).

Joan atzera eta estutu aurretik instalatutako torloju guztiak. M6 torlojuek 10 mm-ko giltza beharko dute, M8-k (hanka euskarri) 13 mm-ko giltza beharko dute.
Ohar: Ez estutu estutu.

Install the Face Panel Tabs (2) to both the face panels, using a short M6 bolt and a lock nut. Tighten with a 10mm wrench. The “lip” should point upwards to create a hanger for the lidhandle while filling feeder.

HANKAK MUNTU ETA INSTALATU

1. Collect all 4 Top-Leg sections. Insert each section into a leg bracket. Set the leg angle to eithe
   
2. Insert the remaining leg sections into the (4) top-leg sections. Tap firmly on the end of the legs when joining leg sections; this will help to keep them locked together.
   

INSTALATU ELIKAGAI-KIT HOPPERAN

Ikusi elikadura-kit osagarriak instalatzeko.

INSTALATU BARNE INBUTUA

Zure elikadura-kit bat zure hopperan instalatu ondoren, sartu barne-inbutua toldian, eta utzi auto-lerrokatze-eraztunak tolgiaren konoaren behealdean.

OHARRA: Ziurtatu barne-inbutua tolgiaren irteeran guztiz eserita dagoela eta tolgiaren behealdean kokatuta dagoela. Inbutuaren lerrokatzea funtsezkoa da elikadura egokirako.

MUNTATU ETA INSTALATU TAPA

1. Instalatu estalkiko fitxak (2) estalkiko muntaketa-zuloetan, estalkiaren BARRUtik M6 torloju labur bat sartuz eta 10 mm-ko giltza batekin estututako azkoin batekin finkatuz. Hauek zure elikaduraren estalkia blokeatzeko aukera emango dizute sarraila estandar gehienak erabiliz.
   
2. Place the lid assembly on top of the feeder with the tabs aligned. The handles should be on the sides of the feeder
   

Gure Zerbitzu Sailak pozik erantzungo dizkizu zure zalantzak argitzeko. www.moultriefeeders.com/support

Dokumentuak / Baliabideak

MOULTRIE MFG-15050 Ranch Series Gravity Feeder Kit [pdf] Argibideak MFG-15050 Ranch Series Gravity Feeder Kit, MFG-15050, Ranch Series Gravity Feeder Kit, Gravity Feeder Kit, Feeder Kit

Erreferentziak

• Elementu berrien bermea | Moultrie Berme politika | Gehiago ikasi