1. Sarrera
This manual provides detailed instructions for the safe and effective use of your Godox K-180A 180Ws Photography Studio Flash Strobe Light Kit. Please read this manual thoroughly before operating the equipment and keep it for future reference.
2. Segurtasun informazioa
Always observe basic safety precautions when using electrical equipment to reduce the risk of fire, electric shock, or injury.
- Ez jarri unitatea euri edo hezetasunera.
- Do not disassemble the unit. If repairs are needed, contact qualified service personnel.
- Ziurtatu potentzia boltage matches the unit's requirements (AC220/60Hz or 110V/60Hz).
- Mantendu haurren eskura.
- Unplug the unit from the power source before cleaning or when not in use.
- Avoid prolonged continuous use of the modeling lamp; allow it to cool down for at least 1 minute after 5 minutes of continuous use to prevent overheating.
3. Paketearen edukia
Verify that all items are included in your package (based on Kit 8, the most comprehensive option):
- 1x Godox K-180A Flash Unit
- 1x RT-16 Trigger (Transmitter and Receiver)
- 1x 180cm Light Stand
- 1x FS50X70cm Grid Softbox
- 1x Modeling Lamp
- 1x korronte elektrikoa
4. Konfiguratzeko argibideak
4.1. Light Stand Assembly
Unfold the light stand legs and extend the telescopic sections to the desired height. Ensure all locking knobs are securely tightened.
4.2. Flash Unit Preparation
- Mount the K-180A flash unit onto the top stud of the light stand.
- Adjust the mounting bracket to achieve the desired angle and securely tighten it.
- The umbrella input is available for attaching a studio umbrella if desired.
4.3. Softbox Assembly
Assemble the FS50X70cm Grid Softbox according to its specific instructions. Attach it to the universal mount on the flash unit.
4.4. RT-16 Trigger Setup
Insert the 23A 12V battery into the transmitter and 2 AAA batteries into the receiver (AAA batteries for receiver not included). Connect the receiver to the flash unit's sync port.
4.5. Energia-konexioa
Connect the power cord to the flash unit's power socket and then to a suitable AC power outlet. Ensure the power switch is in the OFF position before connecting.
5. Funtzionamendu-argibideak
5.1. Piztu/Itzali
Flip the Power Switch (labeled 'POWER') to turn the flash unit ON or OFF. The Charging LED Indicator will illuminate during charging.
5.2. L modelatzeaamp Kontrola
Use the Modeling Light Switch (labeled 'MODEL') to turn the modeling lamp ON or OFF. Pushing it downwards (G position) turns it off, upwards (F position) turns it on. Note: Do not keep the modeling lamp on for too long; it is recommended to cool it down for 1 minute after 5 minutes of continuous use.
5.3. Flash Output Control
Rotate the Flash Output Controller (labeled with '+' and '-') to adjust the flash power. The output is stepless from 1/8 to full power. This allows for precise light requirements in different environments.
5.4. Test botoia
To test the flash or before taking a picture, push the Test Button (labeled 'TEST'). This can also be used to adjust the brightness when combined with the flash output controller.
5.5. Slave Trigger Mode
The flash unit can be triggered synchronously with one external flash. This mode allows the K-180A to act as an auxiliary lamp, argi eta itzal efektu ezberdinak eskainiz.
6. Mantentzea
- Garbiketa: Use a soft, dry cloth to clean the exterior of the flash unit and accessories. Do not use abrasive cleaners or solvents.
- Biltegiratzea: Store the kit in a cool, dry place, away from direct sunlight and excessive humidity.
- Fusiblearen ordezkapena: If the unit fails to power on, check the fuse. Replace it with a fuse of the same rating (5A).
7. Arazoak
- Flasha ez da pizten:
- Check if the unit is powered on and connected correctly.
- Ensure the RT-16 trigger transmitter and receiver have fresh batteries and are properly synced.
- Verify the sync cord is securely connected to the flash unit.
- Egiaztatu fusiblea.
- Modelizazioa lamp ez dabil:
- Ensure the Modeling Light Switch is in the ON position.
- Egiaztatu lamp bulb is securely installed and not burnt out.
- Flasharen irteera ez-koherentea:
- Ensure the Flash Output Controller is set correctly.
- Allow sufficient recharging time between flashes.
8. Zehaztapenak
8.1. Godox K-180A Flash Unit
| Ezaugarri | Zehaztapena |
|---|---|
| Eredua | K-180A |
| Flash Irteera | 180WS |
| Gida-zenbakia (m ISO 100) | 45 |
| Kolore Tenperatura | 5600 ± 200K |
| Potentzia Voltage | AC220/60Hz or 100V/60Hz (Optional, check your unit) |
| Flash Power Kontrola | Stepless (1/8-full) |
| L ereduaamp | 75WS |
| Kargatzeko Denbora | 0.5-3 seg |
| Flash Triggering Model | Sync cord, Test button, Slave |
| Flash iraupena | 1 / 2000-1 / 800 |
| Metxa | 5A |
| Dimentsioa | 17 x 10 x 17.5cm (approx. 7.2 x 4.1 x 5.4in) |
| Pisua | Approx. 0.59KG (approx. 603g / 21.3oz) |
8.2. 180cm Light Stand
| Ezaugarri | Zehaztapena |
|---|---|
| Karga-jasadura | 2kg |
| Telescopic Height | 82-200 cm |
| Biltegiratze altuera | 68 cm |
| Hodiaren Diametroa | Φ1.6/1.9/2.2cm |
| Torlojuaren zuloa | 1/4" |
| Pisua | 0.81kg |
| Tolestutako Luzera | 67 cm |
| Gutxieneko Luzera | 70cm (2'4") |
| Altuera Max | 200cm (7') |
| Ideal Max. Working Height | 140-150 cm |
8.3. FS50X70cm Grid Softbox
| Ezaugarri | Zehaztapena |
|---|---|
| Tamaina | 50 x 70cm / 20" x 27" |
| Mendia | Mendi Unibertsala |
| Pisua | Gutxi gorabehera. 0.6kg |
8.4. RT-16 Wireless Flash Trigger
| Ezaugarri | Zehaztapena |
|---|---|
| Mota | Haririk gabeko Flash Trigger |
| Kanalak | 16 kanal |
| Transmisorearen Potentzia Sarrera | 23A 12V bateria (barne) |
| Hartzailearen Potentzia Sarrera | 2 * AAA batteries (not included) |
| Receiver Plug Size | 3.5 mm |
| Adapter Size for Receiver Plug | 3.5 mm eta 6.35 mm |
| Radio Working Frequency | 433MHz |
| Sinkronizazio abiadura | 1/200eko hamarkada |
| Outdoor Operation Distance | Gehienez 30 m (espazio irekia) |
| Indoor Operation Distance | Gehienez 20 m (espazio irekia) |
| Paketearen tamaina | 21.5 x 7.5 x 3.8 cm / 8.5 x 3.0 x 1.5 hazbeteko |
| Paketearen pisua | 125g / 4.4oz |
9. Erabiltzaileentzako aholkuak
- Argazkigintzaren erabilera: This kit is primarily intended for photography, providing controlled lighting for studio setups. Experiment with different flash power settings and softbox positions to achieve desired lighting effects.
- L ereduaamp Erabilera: While useful for previewing lighting, remember to give the modeling lamp breaks to prevent overheating and prolong its lifespan.
- Trigger Placement: For optimal wireless triggering, ensure a clear line of sight between the RT-16 transmitter and receiver, especially in indoor environments.
10. Bermea eta Laguntza
Bermeari buruzko informazioa, laguntza teknikoa edo zerbitzu-kontsultak egiteko, jarri harremanetan saltzailearekin edo fabrikatzailearekin zuzenean. Gorde erosketa-agiria erosketaren frogagiri gisa.
