SINOTIMER TM630A 12V DC Programmable Digital Timer Switch

Sarrera

The SINOTIMER TM630A is a compact, programmable digital timer switch designed to automatically control various electrical equipment by switching them on and off at preset times. This device is suitable for a wide range of applications, including controlling streetlights, neon signs, lamps, water heaters, air conditioners, billboards, electric cookers, boosters, sprayers, bottlers, preheaters, agriculture facilities, and broadcasting equipment. It features a built-in battery to retain programmed settings during power failures, ensuring reliable operation. The TM630A is built with a high-accuracy CMOS chip, offers strong anti-jamming capabilities, and is simple to set up and operate. It conforms to IEC 60367 standards and is CE certified.

Zehaztapenak

Konfigurazioa

1. Instalazioa

The TM630A timer switch can be installed either on a DIN rail or screw-mounted. Ensure the installation location is dry, well-ventilated, and within the specified temperature range (-20°C to +50°C).

2. Kableatuen Diagrama

Refer to the following wiring diagram for proper connection. Ensure all connections are secure and comply with local electrical codes. This diagram shows the connections for the 12V DC/AC input and the load output.

The timer has two input terminals for power (typically marked L and N for AC, or + and - for DC) and two output terminals for the load.

3. Initial Power-up

Upon initial power-up or after extended storage, the internal 1.2V rechargeable battery may be low. Connect the timer to its power supply (12V DC/AC) for a few hours to allow the internal battery to charge. This battery maintains the programmed settings during power outages.

Funtzionamendu-argibideak

1. Botoiaren funtzioak

Familiarize yourself with the buttons on the front panel:

• C/R (Cancel/Recall): Clears current settings or recalls saved programs.
• D+ (Day): Adjusts the day of the week.
• H+ (Hour): Adjusts the hour.
• M+ (Minute): Adjusts the minute.
• P (Program/Timer): Programazio moduan sartzen da.
• ERLOIA: Used in combination with D+, H+, M+ to set the current time and day.
• ESKULIBURUA: Manually switches the output ON/OFF or sets to AUTO mode.

2. Setting the Present Time and Day

To set the current time and day of the week:

1. Eduki sakatuta ERLOIA botoia.
2. Eusten bitartean ERLOIA, sakatu ORDUA uneko ordua ezartzeko.
3. Eusten bitartean ERLOIA, sakatu MINUTUA uneko minutua ezartzeko.
4. Eusten bitartean ERLOIA, sakatu EGUNA asteko uneko eguna ezartzeko.

3. PIZTE/ITZALDU ordutegiak programatzea

The timer supports up to 16 ON/OFF programs per day or week. Follow these steps to set your desired schedules:

1. Sakatu tenporizadorea (P) button once to enter the 1st ON time setting. The display will show "1 ON".
2. Sakatu ORDUA, MINUTUA, eta EGUNA buttons to set the desired time and day(s) for the 1st ON event.
   • EGUNA button allows selecting various combinations of days (e.g., MO, TU, WE, TH, FR, SA, SU; MO, TU, WE, TH, FR; SA, SU; MO, WE, FR; TU, TH, SA; MO, TU, WE; TH, FR, SA; MO, WE, FR, SA; MO, TU, WE, TH, FR, SA, SU).
3. Sakatu tenporizadorea (P) button again. The display will show "1 OFF".
4. Sakatu ORDUA, MINUTUA, eta EGUNA buttons to set the desired time and day(s) for the 1st OFF event.
5. Repeat steps 1-4 for additional ON/OFF programs (up to 16 pairs).
6. Programazio modutik irteteko, sakatu ERLOIA botoia.

4. Eskuzko gainidaztea

The ESKULIBURUA button allows you to override the programmed settings temporarily or permanently:

• Sakatu ESKULIBURUA repeatedly to cycle through modes: ON (always on), OFF (always off), and AUTO (follows programmed schedule).
• In AUTO mode, the timer will execute the programmed ON/OFF events.

Mantentzea

1. Barne Bateria

The TM630A includes a 1.2V rechargeable internal battery. This battery automatically recharges when the timer is connected to its power supply. It is designed to retain your programmed settings for up to 60 days during power outages. If the timer has been stored for a long period without power, allow it to charge for several hours before programming to ensure full memory retention.

2. Garbiketa

To clean the timer, gently wipe the exterior with a soft, dry cloth. Do not use abrasive cleaners, solvents, or immerse the device in water.

Arazoak konpontzea

• Pantaila hutsik dago: Check if the timer is receiving power (12V DC/AC). If it has been without power for an extended period, the internal battery may be fully discharged. Connect to power and allow it to charge.
• Programs are not executing:
  • Ziurtatu tenporizadorea martxan dagoela AUTO mode (check the display for "AUTO"). Press the ESKULIBURUA button to cycle to AUTO mode if necessary.
  • Verify that the current time and day are set correctly.
  • Check that the ON/OFF programs are correctly entered and enabled.
• Time drift: The timer has an auto time error correction of +/- 30 seconds weekly. Significant deviations may indicate an issue with the power supply or internal components.
• Loss of programs after power outage: While the internal battery provides memory retention for up to 60 days, prolonged power outages or a depleted internal battery can lead to program loss. Ensure the internal battery is adequately charged.

Erabiltzailearen aholkuak

• For critical applications, consider testing your programmed schedules after initial setup to ensure they function as expected.
• Hartu aurreratage of the 15 programming group combinations to create complex weekly schedules for different days or sets of days.
• The manual override function is useful for temporary changes without altering your saved programs.
• Given its wide application range, this timer is highly versatile. Consider using it for automating garden irrigation, aquarium lighting, or even charging cycles for low-voltage gailuak.

Bermea eta Laguntza

The SINOTIMER TM630A timer switch is certified with CE, RoHS, EMC, and LVD standards, indicating compliance with relevant health, safety, and environmental protection directives.

For warranty information, technical support, or service inquiries, please contact your original point of purchase or the manufacturer directly. The product package includes a manual in Russian, Portuguese, and English languages for detailed guidance.