AOLON W3002 Microcomputer Temperature Controller
Zehaztapen Teknikoak
| Zehaztapena | Xehetasunak |
|---|---|
| Produktuaren izena | Microcomputer Temperature Controller (XH-W3002) |
| Neurketa-eremua | -50°C to 110°C (-50°C to 100°C model variation) |
| Kontrol-eremua | -50°C to 110°C (-50°C to 100°C model variation) |
| Tenperatura neurtzeko zehaztasuna | ±0.2°C |
| Tenperatura Kontrolaren Zehaztasuna | ±0.1°C |
| Neurketa-sarrera | NTC10K L=1m waterproof probe |
| Input Power Options | 12V / 24V / 220V AC/DC |
| Irteerako potentzia aukerak | 120W (12V) / 240W (24V) / 1500W (220V) |
| Irteera mota | Irteera zuzena |
| Irteera-gaitasuna | Gehienez 10 A |
| Instalazio-zuloaren distantzia | 73mm (Hole size: 4mm) |
| Neurriak | 60 mm × 45 mm × 31 mm |
Konfigurazio azkarra eta erabilera
- Connect the temperature sensor: use the supplied NTC10K waterproof probe (L=1m).
- Provide power using one supported option: 12V/24V/220V AC/DC.
- Set start temperature (P0): press the Ezarpena button to enter the menu (default to P0), press Ezarpena again, then use Up/Behera to set the desired start temperature.
- Set stop temperature (P1): in the menu, use Up/Behera to select P1, press Ezarpena again, then adjust with Up/Behera.
- (Optional) Calibrate temperature (P2): select P2, press Ezarpena to enter calibration, then set the offset value using Up/Behera.
- (Optional) Set delayed start (P3): select P3 and set the delay time (minutes) using Up/Behera (recommended 3–6 minutes for compressor-based refrigeration; otherwise leave at 0).
Wiring Diagrams & Safety Information
12V / 24V Connection Way
Oharra: 12V/24V power supplies must use a stable DC power source.
220V Connection Way
Abisua: This model is designed with direct output power. Exercise extreme caution when connecting the electricity. Ensure the load is connected to the output terminal port before powering up to prevent potential output short circuit ignition or sparks.
Settings Parameter Menu
| Kodea | Deskribapena | Ezarpen-barrutia | Fabrikako lehenetsia |
|---|---|---|---|
| P0 | Hasierako tenperatura | -50 eta 110 °C artean | 00°C |
| P1 | Gelditu tenperatura | -50 eta 110 °C artean | 00°C |
| P2 | Tenperaturaren zuzenketa | -10 eta 10 °C artean | 0°C |
| P3 | Delay to start | 0 eta 10 minutu | 0 minutu |
Parameter Configurations & Functions
P0: Start-up Temperature Setting
Sakatu Ezarpena button to enter the internal menu. The display will default to P0. Sakatu Ezarpena button once more, then use the Up eta Behera buttons to set your desired start temperature.
Sakatu Ezarpena button to enter the internal menu. When
P0 is displayed, use the Up or Behera aukeratzeko botoiak P1. Sakatu Ezarpena button again, and adjust the target stop temperature using the Up eta Behera botoiak.Sakatu Ezarpena button to enter the internal menu, then switch to
P2 erabiliz Up or Behera botoiak. Sakatu Ezarpena button again to calibrate. Use the Up eta Behera buttons to enter the offset value.Calibration Formula: Detected Temperature + Calibration Temperature = Actual Temperature
- If the detected temperature is 0.5°C higher than the actual temperature: Set P2 to -0.5°C
- If the detected temperature is 1.0°C lower than the actual temperature: Set P2 to 1.0°C
P3: Delayed Start Setting
Sakatu Ezarpena button to enter the internal menu and switch to P3 erabiliz Up or Behera botoiak. Sakatu Ezarpena button again and set the delay time in minutes using the Up or Behera botoiak.
Oharra: This function is typically used for compressor-based refrigeration systems (like refrigerators or freezers) to protect the motor. A delay of 3 to 6 minutes is recommended. If you are not controlling a compressor, leave this set to 0.
Funtzionamendu moduak
Berokuntza moduaAraua:Start-up Temperature (P0) < Stop Temperature (P1) The system automatically determines it is in heating mode when P0 is configured lower than P1.
Exampagertokia:
Control a water heater to turn off when the temperature reaches 50°C and restart heating when the temperature drops back down to 40°C.
- Verify that the heating rule is met: Start-up (40°C) is less than Stop (50°C).
- Sakatu Ezarpena button, enter the menu, select
P0, and adjust the value to 40°C. - Sakatu Ezarpena button, enter the menu, select
P1, and adjust the value to 50°C.
Hozteko moduaAraua: Start-up Temperature (pø) > Stop Temperature (Pl). The system automatically determines it is in cooling mode when P0 is configured higher than P1.
Exampagertokia:
Control a cabinet radiator to turn on when temperatures reach 30°C and stop cooling once the temperature drops to 26°C.
- Verify that the cooling rule is met: Start-up (30°C) is greater than Stop (26°C).
- Sakatu Ezarpena button, enter the menu, select
P0, and adjust the value to 30°C. - Sakatu Ezarpena button, enter the menu, select
P1, and adjust the value to 26°C.
Arazoak konpontzea
Common Fault: Incorrect Settings
If you set your temperature values upside down (e.g., configuring heating parameters with P0 > P1), the output indicator light will remain off and the connected load will not work. Check the temperature values in your P0 eta P1 settings if the system is unresponsive.
With the controller powered on, press and hold both the Up eta Behera buttons simultaneously for approximately 3 seconds. Once the digital tube displays
888, The controller will automatically return to real-time temperature detection, indicating a successful factory reset.- Display “LLL”: Indicates a temperature sensor probe failure. Please inspect, repair, or replace the waterproof probe.
- Display “HHH”: Indicates that the ambient temperature has exceeded the controller’s detection range. Relocate the unit to an appropriate environment.
Dokumentuak / Baliabideak
 | W3002 Microcomputer Temperature Controller |
Erreferentziak
- Erabiltzailearen eskuliburuamanual.tools