Westek TMDCD60 Hardwire Indoor Countdown 6-Setting Wall Switch Timer User Manual

Sarrera

The Westek TMDCD60 is a hardwire indoor countdown timer designed to replace a standard wall switch. It provides timed control for lights, fans, heaters, and other devices, automatically turning them off after a selected duration. This manual provides instructions for safe installation, operation, and maintenance of your timer switch.

Segurtasun Informazioa

OHARRA: Deskarga elektrikoaren arriskua. Improper installation can lead to serious injury or death. Always turn off power at the circuit breaker or fuse box before beginning installation. Consult a qualified electrician if you are unsure about any part of the installation process.

• Gailu hau barrualdean erabiltzeko soilik da.
• Ziurtatu kableatu-konexio guztiak ondo daudela eta tokiko araudi elektrikoak betetzen dituztela.
• Ez gainditu gailuaren balorazio elektrikoak.
• A neutral wire is required for installation. Older homes may not have a neutral wire in the switch box.

Paketearen edukia

• Westek TMDCD60 Countdown Timer Switch
• Argibide eskuliburua (dokumentu hau)

Produktua amaituview

The Westek TMDCD60 timer switch features a single push-button control and LED indicators for selected time settings. It is designed to fit into a standard wall switch box and can be used with a standard rocker wallplate (not included).

1. irudia: Aurrealdea view of the TMDCD60 timer switch. The face includes a single control button and five LED indicators labeled "10 MIN", "20 MIN", "30 MIN", "60 MIN", and "HOLD".

Instalazioa

1. Itzali energia: Locate the circuit breaker or fuse that controls the switch you are replacing. Turn off the power completely before proceeding. Verify power is off using a voltage probatzailea.
2. Kendu lehendik dagoen etengailua: Carefully remove the wallplate and unscrew the existing switch from the wall box. Disconnect the wires from the old switch. Note the connections for reference.
3. Identifikatu kableak: The Westek TMDCD60 timer requires four wires:
   • Hari beltza: Hot (Line)
   • Hari gorria: Load (to the device being controlled)
   • Hari zuria: Neutroa
   • Hari berdea: Lurra

   Ensure your wall box contains a neutral wire. If not, this timer cannot be installed without running a new neutral wire, which should be done by a qualified electrician.

   

   2. irudia: Atzealdea view of the TMDCD60, illustrating the labeled wires for proper connection.
4. Konektatu kableak: Using wire nuts (not included), connect the wires from the wall box to the corresponding wires on the TMDCD60 timer switch:
   • Konektatu Beltza wire from the timer to the Hot (Line) wire from the wall box.
   • Konektatu Gorria wire from the timer to the Kargatu wire from the wall box (to the light/fan).
   • Konektatu Zuria wire from the timer to the Neutroa wire from the wall box.
   • Konektatu Berdea wire from the timer to the Lurra wire from the wall box.
5. Muntatu tenporizadorea: Carefully fold the wires into the wall box. The timer is deeper than a standard switch, so ensure there is enough space. Secure the timer switch to the wall box using the provided screws.
6. Horma-plaka instalatu: Attach a standard rocker wallplate (not included) over the timer switch.
7. Berrezarri boterea: Piztu berriro korrontea etengailu elektrikoan edo fusible-kutxan.

Funtzionamendua

The TMDCD60 timer operates with a single push-button control. Each press cycles through the available countdown settings and the HOLD function.

1. Turning On and Setting Timer: Press the control button once to activate the timer. The timer will cycle through the following settings with each subsequent press:
   • OFF (no LED lit)
   • 10 Minutes (10 MIN LED lights up)
   • 20 Minutes (20 MIN LED lights up)
   • 30 Minutes (30 MIN LED lights up)
   • 60 Minutes (60 MIN LED lights up)
   • HOLD (HOLD LED lights up)

   The connected device will remain on for the selected duration and then automatically turn off. The corresponding LED will indicate the active setting.

2. HOLD funtzioa: To keep the connected device on indefinitely, press and hold the control button for approximately one second until the "HOLD" LED illuminates. In HOLD mode, the device will remain on until you press the button again to turn it off or select a countdown setting.
3. Itzaltzea: To turn off the connected device before the countdown finishes or while in HOLD mode, press the control button until no LEDs are lit.

Mantentzea

The Westek TMDCD60 timer switch requires minimal maintenance. To clean the surface, wipe with a soft, damp zapirik. Ez erabili garbitzaile edo disolbatzaile urratzailerik. Ziurtatu argindarra itzalita dagoela garbitu aurretik.

Arazoak konpontzea

Zehaztapenak

• Eredua: TMDCD60
• Marka: Westek
• Kolorea: Zuria
• Sarrera boltage: 120V AC 60Hz
• Gehienezko karga: 15A Resistive, 1000W Tungsten, 500VA Ballast, 1/4 HP Motor
• Tenporizadorearen ezarpenak: 10, 20, 30, 60 minutes, HOLD
• Neurriak: 1"D x 1"W x 1"H (Note: These dimensions typically refer to packaging; the device itself is deeper for in-wall installation.)
• Elementuaren pisua: 4.48 ontza
• Muntatze mota: Horma
• Aldatu estiloa: Etengailu baskulatzailea
• Hari neutroa: Beharrezkoa

Bermea eta Laguntza

This Westek product is covered by a 1 urteko berme mugatua erosketa-datatik aurrera. Berme honek ohiko erabileran materialen eta eskulanen akatsak estaltzen ditu.

For technical support or warranty claims, please contact Westek customer service. You can find more information and contact details on the official Westek webgunea bisitatuz edo Westek Store on Amazon.