1. Sarrera
Thank you for choosing the SEACHOICE All-Round Light, 22in. Model 05591. This light is designed to provide reliable 2 nautical mile (NM) visibility for sail or powerboats under 66 feet (20 meters) in length. It meets CE and USCG requirements and NMMA certification procedures, ensuring compliance with marine safety standards. This manual provides essential information for the proper installation, operation, and maintenance of your all-round light.
2. Segurtasun informazioa
- Always disconnect power before installing, servicing, or cleaning the light.
- Ziurtatu kableatu guztiak ondo isolatuta daudela eta zirkuitulaburrak eta korrosioa saihesteko.
- Verify that the power supply matches the light's voltage-eskakizunak (12V DC).
- Do not modify the light in any way, as this may compromise its performance and safety compliance.
- Consult a qualified marine electrician if you are unsure about any installation steps.
3. Konfigurazioa eta instalazioa
Proper installation is crucial for the performance and compliance of your all-round light. Follow these steps carefully:
3.1 Muntatzeko kokapena
The all-round light must be mounted in a position that provides an unobstructed view of the light from all directions (360 degrees) when the vessel is underway. Ensure it is positioned above other obstructions on the vessel.
3.2 Oinarrizko instalazioa
- Select a flat, stable surface for mounting. The Stow-A-Way base measures 3-1/4 inches by 1-5/8 inches.
- The base is predrilled to accommodate No. 8 screws (not included). Use appropriate marine-grade fasteners for your vessel's material.
- Securely fasten the chrome-plated zinc base to the chosen location.
3.3 Kableatua
- This light operates on a 12V DC electrical system.
- Connect the light's positive wire to a switched 12V DC power source, typically through a fuse or circuit breaker on your boat's electrical panel.
- Konektatu argiaren kable negatiboa zure ontziko lurrerako puntu egoki batera.
- Ensure all connections are watertight and protected from corrosion.
Figure 1: The SEACHOICE All-Round Light, 22in. Model 05591, showing its pole and light head. This image illustrates the overall design of the navigation light.
4. Funtzionamendu-argibideak
Once properly installed, operating your SEACHOICE All-Round Light is straightforward:
- Ensure your vessel's 12V DC power system is active.
- Activate the switch connected to the all-round light circuit. The light should illuminate immediately.
- Verify that the light is functioning correctly before operating your vessel, especially during periods of reduced visibility or at night.
- The light provides 2 nautical miles of visibility, making your vessel visible from all directions as required by navigation rules.
5. Mantentzea
Regular maintenance will ensure the longevity and optimal performance of your all-round light.
5.1 Garbiketa
- Periodically clean the lens with fresh water and a soft cloth to remove salt spray, dirt, and grime.
- Avoid abrasive cleaners or solvents that could damage the lens material.
5.2 lamp Ordezkoa
- The light uses a 12V DC-15 CP (Candlepower) lamp.
- If the light fails to illuminate, first check the fuse or circuit breaker. If these are functional, the lamp ordezkoa beharko luke.
- l ordezkatzekoamp, carefully open the light housing (refer to the product diagram if available, or gently pry open if designed for user access).
- Ordeztu l zaharraamp with a new 12V DC-15 CP lamp mota berekoak.
- Ensure the housing is securely closed and watertight after replacement.
5.3 Iragazgaitza den ezaugarria
The light is designed to be waterproof. Regularly inspect the seals and gaskets for any signs of wear or damage. Replace them if necessary to maintain the waterproof integrity.
6. Arazoak
| Arazoa | Kausa posiblea | Irtenbidea |
|---|---|---|
| Argiak ez du argitzen. | No power, blown fuse/tripped breaker, faulty wiring, burnt-out lamp. | Check power supply. Inspect and replace fuse or reset breaker. Verify wiring connections. Replace lamp (ikus 5.2 atala). |
| Argia ahula da edo keinuka ari da. | Bolumen baxuatage, poor connection, corroded terminals, aging lamp. | Egiaztatu bateria bolumenatage. Clean and secure all electrical connections. Replace lamp. |
| Ura argiaren karkasaren barruan. | Damaged seal or gasket, improper reassembly after maintenance. | Disassemble, dry components, inspect and replace seals/gaskets. Reassemble carefully ensuring watertight seal. |
7. Zehaztapenak
- Eredua: 05591
- liburukiatage: 12V DC
- Lamp Mota: 15 CP (Candlepower)
- Ikusgarritasuna: 2 Nautical Miles (NM)
- Vessel Length: For sail or powerboats under 66 ft (20 m)
- Oinarrizko neurriak: 3-1/4 in. x 1-5/8 in. (Stow-A-Way base)
- Muntaketa: Predrilled for No. 8 screws
- Oinarrizko materiala: Chrome Plated Zinc
- Ezaugarri berezia: Iragazgaitza
- Betetzea: Meets CE, USCG, and NMMA certification procedures
8. Bermea eta Laguntza
For warranty information and technical support, please refer to the documentation provided at the point of purchase or contact your retailer. You may also visit the official SEACHOICE weblaguntza gehiago jasotzeko gunea.
For additional information, you can visit the SEACHOICE denda Amazonen.
