1. Sarrera
This manual provides essential information for the safe and correct installation, operation, and maintenance of your Legrand E14 Lamp Holder, model LEG91123. This product is designed for use with E14 screw-base bulbs, with a maximum wattage of 60W and operating at 230 Volts.
2. Segurtasun informazioa
WARNING: Risk of electric shock. Always disconnect power at the main circuit breaker before installing or servicing electrical components.
- Instalazioa elektrizista kualifikatu batek edo pertsona eskudun batek bakarrik egin behar du.
- Ensure the power supply is completely off before beginning any work.
- Ez gainditu gehienezko wat-atage of 60W for the connected bulb.
- Egiaztatu konexio guztiak seguru daudela eta behar bezala isolatuta daudela.
- This product is designed for indoor use in dry locations only.
3. Produktuaren osagaiak
The Legrand E14 Lamp Holder consists of several parts designed for secure and reliable bulb connection.
Figure 3.1: Complete Legrand E14 Lamp Holder. This image shows the complete Legrand E14 lamp holder, featuring the threaded body for bulb insertion and the base for electrical connection.
Figure 3.2: Legrand E14 Lamp Holder disassembled. This image illustrates the main components of the Legrand E14 lamp holder, including the outer casing, internal mechanism, and shade ring.
- Kanpoko Casing: Made of white polyamide material, providing insulation and protection.
- Barne Mekanismoa: Contains the electrical contacts and wiring terminals.
- Shade Ring: Used to secure a lampitzala lamp titularra.
4. Instalatzeko jarraibideak
Follow these steps for proper installation of the Legrand E14 Lamp Titularra.
- Prestatu kableatua: Ensure the power supply is disconnected. Strip approximately 8-10mm of insulation from the ends of the electrical wires.
- Access Terminals: Lamp holder's internal mechanism may need to be partially disassembled to access the wiring terminals. Refer to Figure 3.2 for component identification.
- Konektatu kableak: Insert the stripped wire ends into the designated terminals. The wire entry can be from the side or via a screw connection. Secure the wires firmly by tightening the terminal screws. Ensure no loose strands are present.
Figure 4.1: Internal wiring terminals. This image displays the internal wiring terminals of the Legrand E14 lamp holder, where electrical wires are connected.
- Berriz muntatu: Carefully reassemble the lamp holder components, ensuring all parts are correctly aligned and secured.
- Muntaketa: Lamp holder is designed for installation on a Ø10 male connector. Secure the lamp holder to the fixture using the appropriate mounting method.
- Attach Shade Ring (Optional): al erabiliz geroampshade, slide the shade ring over the threaded part of the lamp holder and tighten it to secure the lampitzala.
5. Funtzionamendua
Behin instalatuta, l-a martxan jartzeaamp holder is straightforward:
- Txertatu bonbilla: Gently screw an E14 screw-base bulb into the lamp holder until it is snug. Do not overtighten.
- Berrezarri boterea: Piztu korronte-iturria zirkuitu-etengailu nagusian.
- Proba: Activate the light switch to confirm proper operation.
6. Mantentzea
The Legrand E14 Lamp Holder requires minimal maintenance.
- Garbiketa: Disconnect power before cleaning. Wipe the exterior with a dry, soft cloth. Do not use abrasive cleaners or solvents.
- Ikuskapena: Aldian-aldian ikuskatu lamp holder for any signs of damage, wear, or loose connections. If any issues are found, disconnect power and address them immediately.
- Bonbillaren ordezkoa: Always disconnect power before replacing a bulb. Allow the old bulb to cool completely before removal.
7. Arazoak
Zure l-rekin arazoak badituzuamp holder, refer to the following common problems and solutions:
| Arazoa | Kausa posiblea | Irtenbidea |
|---|---|---|
| Argia ez da pizten | Ez dago elikadura hornidurarik | Egiaztatu zirkuitu-hauslea eta hormako etengailua. |
| Argia ez da pizten | Bonbilla akastuna | Replace the bulb with a new, working E14 bulb (max 60W). |
| Argia ez da pizten | Kableatu konexio soltea | Disconnect power and check all wire connections within the lamp holder. Tighten if necessary. |
| Argi distiratsua | Bonbilla edo konexio soltea | Ensure the bulb is screwed in tightly. Disconnect power and check wiring connections. |
8. Zehaztapen Teknikoak
- Marka: Legrand
- Modelo zenbakia: LEG91123
- Bonbilla mota: E14 Screw-base
- Materiala: Polyamide-Imide
- Kolorea: Zuria
- liburukiatage: 230 Volt
- Gehienezko potentzia: 60 Watt
- Produktuaren neurriak (L x W x H): 3 x 3 x 6 cm
- Pisua: 50 gramo
- Muntatze mota: For Ø10 male connector
- Compliant Specifications: NF
- Jatorrizko herrialdea: Txina
9. Bermea eta Laguntza
For warranty information or technical support, please refer to the documentation provided with your purchase or contact Legrand customer service directly. Keep your proof of purchase for warranty claims.
