Lutron NTSTV-DV-WH irristagailu-erregulagailuaren argibideen eskuliburua

1. Produktua amaitu daview

The Lutron NTSTV-DV-WH is a Nova T fluorescent/LED single-pole slide dimmer designed for precise control of lighting levels. It features a classic thin profile with a linear slide mechanism for light level selection and an 'off' position. This dimmer is compatible with IEC60929 Annex E compliant LED drivers and electronic fluorescent ballasts.

Ezaugarri nagusiak:

• Single-pole operation for 120/277V systems.
• Supports 0-10V dimming control.
• 8 Amp egungo balorazioa.
• Linear slide for intuitive light level adjustment.
• Adjustable high and low-end trim settings for fine-tuning.
• Requires Lutron PP-20 power pack for loads exceeding 8 amps (bereiz saltzen da).

Image Description: A white rectangular wall plate with a vertical slot in the center. Within the slot, a small white horizontal slide control is visible, positioned towards the bottom. The word "LUTRON" is subtly embossed on the slide control. The overall appearance is clean and minimalist.

2. Segurtasun informazioa

Please read and understand all instructions before installation. Improper installation can result in serious injury or death. This device must be installed by a qualified electrician in accordance with all national and local electrical codes.

• OHARRA: To avoid fire, shock, or death, turn off power at the circuit breaker or fuse box and test that power is off before wiring.
• Do not use this device with any load type other than specified (IEC60929 Annex E compliant LED drivers and electronic fluorescent ballasts).
• Ziurtatu kable-konexio guztiak ondo isolatuta eta ondo finkatuta daudela.
• Do not install if the product appears damaged.
• Funtzionamendu-tenperatura: 0 °C eta 40 °C (32 °F eta 104 °F).

3. Instalatzeko jarraibideak

3.1. Hasi aurretik

1. Itzali etengailuaren edo fusibleen panelean.
2. Remove the existing wall plate and switch/dimmer.
3. Verify the wiring configuration in your wall box. This dimmer is designed for single-pole applications.
4. Ensure the load (LED drivers or fluorescent ballasts) is compatible with 0-10V dimming and the dimmer's specifications (120/277V, 8A max).

3.2. Kableatua

The NTSTV-DV-WH dimmer typically has two black wires for line/load connections and two low-voltage wires (often purple and gray/pink) for 0-10V control. The black line and load wires are interchangeable; either can be connected to the incoming power (line) and the other to the fixture (load). The 0-10V control wires are typically marked for polarity (e.g., '+' and '-').

• Connect one black dimmer wire to the incoming hot wire from the circuit breaker.
• Connect the other black dimmer wire to the load wire leading to the lighting fixture.
• Connect the ground wire from the wall box to the dimmer's ground screw (if present) or splice with the dimmer's ground wire.
• Connect the 0-10V control wires from the dimmer to the corresponding 0-10V control wires on the compatible LED driver or fluorescent ballast, observing polarity.
• 8tik gorako zametarako amps, a Lutron PP-20 power pack is required and must be wired according to its separate instructions.

3.3. Muntaketa

1. Carefully fold wires into the wall box, ensuring no wires are pinched.
2. Secure the dimmer to the wall box using the provided screws.
3. Lotu hormako plaka.
4. Berrezarri energia etengailuan.

4. Operating Your Dimmer

4.1. Light Level Adjustment

To adjust the light level, simply slide the control lever up or down. Sliding the lever upwards increases the light intensity, while sliding it downwards decreases the intensity. Sliding the lever all the way down will turn the lights off.

4.2. Fine-Tuning (Trim Adjustment)

The NTSTV-DV-WH dimmer includes adjustable high-end and low-end trim screws located behind the cover plate. These allow for fine-tuning the maximum and minimum light output to optimize performance with your specific lighting fixtures.

• Remove the wall plate to access the trim screws.
• Use a small screwdriver to adjust the screws.
• Adjust the high-end trim to prevent flickering at maximum brightness.
• Adjust the low-end trim to ensure stable dimming at the lowest desired light level without the lights turning off prematurely.
• Replace the wall plate once adjustments are complete.

5. Mantentzea

The Lutron NTSTV-DV-WH dimmer requires minimal maintenance.

• To clean the dimmer, wipe with a soft, damp oihal. Ez erabili garbitzaile edo disolbatzaile urratzailerik.
• Ensure the dimmer and wall plate are free from dust and debris to maintain proper operation and appearance.
• Periodically check for any loose connections or signs of wear, especially during other electrical maintenance.

6. Arazoak

If you experience issues with your Lutron NTSTV-DV-WH dimmer, refer to the following common solutions:

If the problem persists after attempting these solutions, contact Lutron technical support.

7. Zehaztapen Teknikoak

8. Bermea eta Laguntza

For warranty information and technical assistance, please contact Lutron customer support directly. Lutron is known for providing excellent technical support to assist with product inquiries and troubleshooting.

You can typically find contact information on the official Lutron webgunean edo produktuaren ontzian.