Einhell TC-JS 80 600W Jigsaw Instruction Manual

1. Sarrera

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Einhell TC-JS 80 600W Jigsaw. Please read this manual thoroughly before using the tool and keep it for future reference.

The Einhell TC-JS 80 is a powerful jigsaw designed for various cutting tasks. It features an adjustable 4-position pendulum function and electronic speed control for adapting to different materials. Its design includes dust extraction capability and a rotating saw shoe for miter cuts up to 45°.

2. Segurtasun-argibideak

Erremintaren segurtasun-abisu orokorrak:

• Always wear eye protection and hearing protection when operating the jigsaw.
• Mantendu lan-eremua garbi eta ondo argiztatuta. Eremu nahasiak edo ilunek istripuak gonbidatzen dituzte.
• Ez erabili tresna elektrikoak atmosfera lehergarrietan, adibidez, likido sukoiak, gasak edo hautsak daudenean.
• Mantendu haurrak eta ingurukoak urrun, erreminta elektrikoa erabiltzen duzun bitartean. Distrakzioek kontrola galtzea eragin dezakete.
• Ensure the power cord is not damaged and is kept away from heat, oil, sharp edges, or moving parts.
• Deskonektatu beti tresna korronte-iturritik doikuntzak egin, osagarriak aldatu edo tresna gorde aurretik.
• Ziurtatu laneko pieza. Erabili clamps edo tornu bat lan-pieza ondo eusteko.
• Ez ezazu gainditzen. Mantendu oin eta oreka egokia uneoro.
• Erabili zure aplikaziorako tresna egokia. Ez behartu tresna.
• Mantendu tresnak kontu handiz. Mantendu ebakitzeko tresnak zorrotz eta garbi.
• Egiaztatu pieza mugikorren lerrokadura desegokia edo lotzea, piezak apurtzea eta erremintaren funtzionamenduan eragina izan dezakeen beste edozein egoera.

Specific Jigsaw Safety Warnings:

• Hold the tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring or its own cord.
• Erabili clamps edo piezak plataforma egonkor batean babesteko eta eusteko beste modu praktiko bat.
• Ziurtatu xafla zorrotza dela eta moztu beharreko materialarentzat egokia dela.
• Do not touch the blade immediately after use, as it may be hot.

3. Produktua amaitu daview eta Osagaiak

Familiarize yourself with the various parts of your Einhell TC-JS 80 Jigsaw.

3.1. irudia: Orokorrean view of the Einhell TC-JS 80 Jigsaw.

This image shows the complete jigsaw unit, highlighting its compact design and the attached saw blade with a parallel guide for precise cuts.

• Heldulekua: Ergonomikoki diseinatua helduleku erosoa lortzeko.
• Piztu/Itzali etengailua: Located on the handle for easy access.
• Abiadura kontrolatzeko markaketa: Allows adjustment of cutting speed.
• Pendulum Function Selector: Adjusts the blade's orbital action for faster or finer cuts.
• Zerra Pala Clamp: Secures the saw blade in place.
• Base Plate (Saw Shoe): Supports the tool on the workpiece and can be angled for miter cuts.
• Hautsa erauzteko ataka: For connecting a dust extraction system.
• Gida paraleloa: Assists in making straight cuts parallel to an edge.

Figure 3.2: Detail of the blade clamping mekanismo.

This image provides a closer look at the area where the saw blade is inserted and secured, including the blade guide roller.

Figure 3.3: Ergonomic handle design.

This image highlights the comfortable, non-slip grip of the jigsaw's handle, designed for user comfort during operation.

Figure 3.4: Speed control dial.

This image shows the dial used to adjust the electronic speed control, allowing the user to select the appropriate cutting speed for different materials.

4. Konfigurazioa

4.1. Zerra-xafla instalatzea

1. Ziurtatu zerra elektrikoa korronte-iturritik deskonektatuta dagoela.
2. Locate the hex lock/Allen key for the blade clamp.
3. Loosen the screw on the blade clamp Allen tekla erabiliz.
4. Sartu zerra xafla clamp hortzak aurrera begira dituela.
5. Ensure the back of the blade fits into the guide roller.
6. Tighten the screw firmly to secure the blade. Do not overtighten.

4.2. Adjusting the Base Plate for Miter Cuts

The base plate can be angled up to 45° for miter cuts.

1. Unplug the jigsaw.
2. Loosen the screws that secure the base plate to the main body of the jigsaw.
3. Tilt the base plate to the desired angle (up to 45° left or right). Use a protractor for accuracy if needed.
4. Tighten the base plate screws securely.

Figure 4.1: Flexible cuts up to 45 degrees.

This graphic demonstrates the capability of the jigsaw to perform angled cuts by tilting its base plate up to 45 degrees in either direction.

5. Funtzionamendu-argibideak

5.1. Piztu/Itzaltzea

• To turn on the jigsaw, press the On/Off switch.
• To turn off, release the On/Off switch.

5.2. Abiadura doitzea

The electronic speed controller allows you to adjust the cutting speed based on the material and desired finish.

• Rotate the speed control dial (Figure 3.4) to increase or decrease the blade strokes per minute.
• Lower speeds are generally used for harder materials or for more precise cuts.
• Higher speeds are suitable for softer materials and faster cutting.

Figure 5.1: Speed vs. Exact cutting.

This graphic illustrates the difference between high-speed cutting (for quick material removal) and exact cutting (for precision), which can be controlled by the electronic speed setting.

5.3. Using the Pendulum Function

The 4-position pendulum function controls the orbital action of the blade, affecting cutting speed and finish.

• 0 posizioa (pendulurik gabe): For fine cuts, cutting thin materials, or cutting metal. The blade moves straight up and down.
• Positions I, II, III (Increasing Pendulua): For faster cutting in wood and other soft materials. The blade moves in an elliptical motion, clearing chips more aggressively.
• Adjust the pendulum selector lever to the desired position.

Figure 5.2: Pendulum function settings.

This graphic visually explains how the pendulum function alters the blade's movement, from a straight up-and-down motion to an orbital motion, for varying cutting speeds and finishes.

5.4. Hautsa erauztea

For a cleaner work environment, connect a dust extraction system to the dust extraction port.

• Attach a suitable vacuum cleaner hose to the dust extraction port at the rear of the jigsaw.
• Ensure the connection is secure before operating the tool.

6. Mantentzea

Mantentze-lan erregularrak zure puzzle-zerraren iraupena eta errendimendu optimoa bermatzen ditu.

6.1. Garbiketa

• Deskonektatu beti tresna garbitu aurretik.
• Garbitu aireztapen-zirrikituak aldizka gehiegi berotzea saihesteko.
• Remove dust and debris from the blade area and base plate after each use.
• Erabili eskuila leun bat edo aire konprimatua garbitzeko. Ez erabili disolbatzailerik edo garbitzaile urratzailerik.

6.2. Pala ordezkatzea

Replace dull or damaged saw blades promptly to ensure efficient and safe cutting. Refer to Section 4.1 for blade installation steps.

6.3. Biltegiratzea

• Gorde puzzle-zerra leku lehor eta seguru batean, haurren eskura ez dagoen lekuan.
• Ziurtatu elikatze-kablea ondo kiribilduta dagoela eta ez dela tolestuta.

7. Arazoak

8. Zehaztapenak

9. Bermea eta Laguntza

For warranty information and technical support, please refer to the documentation provided with your purchase or contact Einhell customer service directly. Keep your proof of purchase for warranty claims.

EBko ordezko piezen erabilgarritasunaren iraupena: 1 Urte