1. Sarrera
This manual provides essential information for the safe and efficient operation of your Einhell GC-DW 1045 N Deep Well Pump. Please read these instructions carefully before initial use and keep them for future reference. This robust base pump is designed for pumping clear and service water for garden and household use, featuring a multi-stage impeller for constant pressure and a powerful motor.
Image: The Einhell GC-DW 1045 N Deep Well Pump with its included drain rope.
2. Segurtasun-argibideak
Always observe the following safety precautions to prevent injury and damage to the pump:
- Ensure the power supply matches the pump's specifications (230 V).
- Ez erabili ponpa leherketa-egoeretan edo likido sukoiekin.
- Never pull the pump by its power cable. Use the provided drain rope for lowering and retrieving.
- Protect the pump from frost. Disconnect and drain it during winter months if not in continuous use.
- Ensure the well or bore hole has sufficient operating space (minimum 99 x 99 mm) to prevent the pump from getting stuck.
- The pump is equipped with thermal overload protection. If it overheats, it will shut off automatically. Allow it to cool down before restarting.
3. Konfigurazioa
- Despaketatzea: Carefully remove the pump and all accessories from the packaging. Check for any transport damage.
- Connecting the Pressure Hose: Attach a suitable pressure hose to the pump's discharge connection. Ensure a tight, leak-free seal.
Image: Close-up of the pump's pressure connection point.
- Attaching the Drain Rope: Securely fasten the provided drain rope to the designated eyelets on the pump. This rope is crucial for safe lowering and retrieval.
Image: The deep well pump with the drain rope attached, ready for deployment.
- Ponpa jaistea: Carefully lower the pump into the well using the drain rope. Ensure the pump hangs freely and does not touch the bottom or sides of the well. Maintain the minimum operating space of 99 x 99 mm.
Image: Diagram illustrating the required minimum operating space of 99 x 99 mm for the pump in a well.
Image: Diagram showing the deep well pump submerged in a water source.
- Konexio elektrikoa: Connect the pump to a properly grounded power outlet (230 V). Ensure the connection is protected from moisture.
4. Funtzionamendua
Once properly installed, operating the Einhell GC-DW 1045 N is straightforward:
- Hasierako hasiera: After ensuring all connections are secure and the pump is fully submerged, switch on the power. The pump will begin to draw water. It may take a few moments for water to flow consistently as air is purged from the system.
- Etengabeko funtzionamendua: Multi-stage impeller ensures constant pressure and efficient water delivery. The pump is designed for continuous operation within its specified limits.
- Jarraipena: Periodically check the water flow and pump sound. Any unusual noises or reduced flow may indicate an issue.
Image: A person preparing to install the deep well pump into a well opening.
Image: Diagram showing the multi-stage impeller system inside the pump, designed for consistent pressure.
5. Mantentzea
Regular maintenance ensures the longevity and optimal performance of your deep well pump:
- Cleaning the Dirt Sieve: The pump is equipped with a dirt sieve. If water flow decreases significantly, the sieve may be clogged. Retrieve the pump and clean the sieve as needed.
Image: Close-up of the dirt sieve at the bottom of the pump.
- Konexioak egiaztatzea: Periodically inspect all hose and electrical connections for wear, damage, or leaks.
- Neguan egitea: If the pump will not be used during freezing temperatures, it must be removed from the well, thoroughly drained, and stored in a frost-free environment.
- Zigilu mekanikoa: The high-quality mechanical seal is designed for long service life and generally requires no maintenance.
6. Arazoak
Bezeroarentzako arreta-zerbitzura deitu aurretik, saiatu arazo ohikoenetarako irtenbide hauekin:
| Arazoa | Kausa posiblea | Irtenbidea |
|---|---|---|
| Ponpa ez da martxan jartzen. | No power supply; Thermal overload protection activated. | Check power connection and circuit breaker; Allow pump to cool down for 30 minutes. |
| Ur emaria baxua edo ez. | Clogged dirt sieve; Air in the system; Hose kinked or blocked; Water level too low. | Clean dirt sieve; Ensure pump is fully submerged and primed; Check hose for obstructions; Verify sufficient water in well. |
| Pump motor hums but does not pump. | Impeller blocked; Air lock. | Disconnect power, retrieve pump and check for obstructions around impeller; Ensure pump is properly submerged and primed. |
Irtenbide hauek saiatu ondoren arazoak konpontzen ez badira, jarri harremanetan zerbitzu-langile kualifikatuekin.
7. Zehaztapenak
| Ezaugarri | Balioa |
|---|---|
| Modelo zenbakia | 4170955 |
| Boterea | 1000 Watt |
| liburukiatage | 230 Volt |
| Gehienez Jario tasa | 6500 litro orduko |
| Buruaren altuera maximoa | 45 metro |
| Ponparen diametroa | 99 mm (implied from operating space) |
| Materiala | Altzairu herdoilgaitza |
| Elementuaren pisua | 7.7 kilogramo |
| Neurriak (L x W x H) | 73 x 14 x 22 cm |
| Bidalketa barne | Deep well pump; Drain rope |
Image: Icon indicating a flow rate of 6500 liters per hour.
Image: Icon indicating a maximum head height of 45 meters.
8. Bermea eta Laguntza
Einhell offers extended warranty services for its products:
- Berme Hedatua: Einhell extends the warranty period for all Einhell Power X-Change batteries and Einhell devices to 3 years.
- Aktibazioa: To activate the extended warranty, Einhell products must be registered on the official Einhell webgunean erosi eta 30 eguneko epean.
Image: Einhell 3-year warranty logo, indicating extended warranty upon online registration.
For further support, technical assistance, or to register your product, please visit the official Einhell website or contact their customer service department. Keep your purchase receipt and model number handy when seeking support.
Informazio gehiago eta harremanetarako datuak aurki ditzakezu hemen: Einhell Store Page.
