SIIG HDMI IP Extender Transmitter (CE-H23B11-S1) User Manual

Sarrera

This manual provides detailed instructions for the installation, operation, and maintenance of the SIIG HDMI IP Extender Transmitter (Model CE-H23B11-S1). This device is designed to transmit HDMI signals with stereo audio over a UTP CAT5e/6 cable up to 120 meters (394 feet). It supports HDbit-T protocol with H.264 compression, enabling a scalable matrix configuration over a dedicated IP network.

Paketearen edukia

Verify that all items listed below are included in your package. If any items are missing or damaged, please contact your vendor for assistance.

• 1x SIIG HDMI IP Extender Transmitter (CE-H23B11-S1)
• 1 elikadura egokitzailea (DC 5V)
• 1x IR Blaster kablea
• 1x IR hargailuaren kablea
• 1x RS-232 Terminal Block
• 2x Muntatzeko euskarriak torlojuekin
• 1x Erabiltzailearen eskuliburua

Image: Contents of the SIIG HDMI IP Extender Transmitter package.

Image: Various accessories for the SIIG HDMI IP Extender system, including power adapters, IR cables, remote, and mounting brackets.

Produktuaren Ezaugarriak

• Extends HDMI signals with stereo audio over a single UTP CAT5e/6 cable up to 120 meters (394 feet).
• Supports HDbit-T protocol with H.264 compression for efficient data transmission over IP.
• Scalable TX/RX Matrix configuration over a dedicated IP network, supporting up to 256 total units (maximum 100 transmitters).
• Supports video resolutions up to 1080p @60Hz.
• Features an HDMI local output (loop-out) on the transmitter for monitoring the source signal.
• Includes IR pass-back function for controlling the source device from the receiver location.
• Provides RS-232 pass-through for controlling RS-232 enabled devices.
• Compatible with computer control software for source selection and switching in Matrix mode.
• Durable metal housing for enhanced longevity.

Image: Front panel of the Transmitter unit, highlighting the IR sensor, power indicator, TX ID display, and reset button.

Konfigurazioa eta konexioak

Follow these steps to set up your SIIG HDMI IP Extender Transmitter. A compatible receiver unit (Model CE-H23C11-S1) and a dedicated unmanaged IGMP Gigabit Switch are required for a complete system.

Osagaien identifikazioa

Image: Front and rear panel port and indicator identification for the Transmitter.

• 5 V DC: Energia-sarrerako jack-a.
• RJ45 IRTEERA: Connects to the network switch or directly to a receiver unit via CAT5e/6 cable.
• IR IRTEERA: IR Blaster kableari konektatzen zaio iturburu-gailua kontrolatzeko.
• HDMI Local Output (Loop-Out): Connects to a local display for monitoring the HDMI source.
• HDMI Sarrera: Connects to the HDMI source device (e.g., Blu-ray player, PC).
• RS-232: Terminal block for RS-232 serial control.
• IR sentsorea: Receives IR signals from a remote control (on the front panel).
• Power LED: Potentzia-egoera adierazten du.
• TX ID: Digital display for Transmitter ID.
• Berrezarri: Button to reset the unit.

Connection Steps (Point-to-Point)

1. Connect your HDMI source device (e.g., DVD player, PC) to the HDMI Sarrera port of the Transmitter unit using an HDMI cable.
2. (Optional) Connect a local display to the HDMI Local Output port of the Transmitter unit using an HDMI cable to monitor the source.
3. Konektatu RJ45 IRTEERA port of the Transmitter unit to the RJ45 SARTU port of a compatible SIIG HDMI IP Extender Receiver unit (sold separately) using a single CAT5e/6 Ethernet cable.
4. Konektatu korronte egokitzaileari DC 5V power jack of the Transmitter unit and plug it into an electrical outlet.
5. Ensure the Receiver unit is also powered on and connected to its display.

Matrix Connection (Many-to-Many)

For a matrix setup, multiple transmitters and receivers are connected via a dedicated unmanaged IGMP Gigabit Switch. This allows any source to be routed to any display.

Irudia: Adibample of a Many-to-Many Matrix Connection using an IGMP Switch.

1. Connect all HDMI source devices to their respective SIIG HDMI IP Extender Transmitter units via the HDMI Sarrera portuak.
2. Konektatu RJ45 IRTEERA port of each Transmitter unit to an available port on a dedicated unmanaged IGMP Gigabit Switch using CAT5e/6 Ethernet cables.
3. Konektatu RJ45 SARTU port of each SIIG HDMI IP Extender Receiver unit (sold separately) to an available port on the same IGMP Gigabit Switch using CAT5e/6 Ethernet cables.
4. Connect each Receiver unit to its respective HDMI display via the HDMI irteera portua.
5. Connect power adapters to all Transmitter and Receiver units and plug them into electrical outlets.
6. Garrantzitsua: A dedicated unmanaged IGMP Gigabit Switch is highly recommended for optimal performance and reliability in matrix configurations. Ensure the switch supports IGMP functionality.

Funtzionamendu-argibideak

Piztu

After all connections are made, plug in the power adapters for both the Transmitter and Receiver units. The Power LED on the front panel of the Transmitter will illuminate.

TX ID Display

The TX ID display on the front panel shows the identification number of the transmitter. In a matrix setup, each transmitter should have a unique ID for proper routing. Refer to the system's control software manual for configuring TX IDs.

IR Pass-Back Function

To control your HDMI source device from the remote display location:

1. Konektatu IR hargailuaren kablea IR IN port on the Receiver unit (sold separately). Position the IR receiver eye to face your remote control.
2. Konektatu IR Blaster kablea IR IRTEERA port on the Transmitter unit. Position the IR blaster emitter directly over the IR sensor of your HDMI source device.
3. You can now use your source device's remote control from the display location to send commands back to the source.

RS-232 pasabidea

The RS-232 terminal block allows for serial control of RS-232 enabled devices. Connect your RS-232 control device to the terminal block on either the Transmitter or Receiver unit to extend control signals.

Matrix Kontrol Softwarea

For matrix configurations, SIIG provides computer control software to manage source selection and switching. Refer to the separate software manual for installation and operation instructions. This software allows you to route any transmitter's signal to any connected receiver.

Arazoak konpontzea

• Irudi/seinalerik ez:
  • Ziurtatu HDMI eta Ethernet kable guztiak ondo konektatuta daudela.
  • Verify that both the Transmitter and Receiver units are powered on.
  • Check the HDMI source device and display for proper operation.
  • Test with shorter or different HDMI/Ethernet cables.
  • Ensure the Ethernet cable is CAT5e/6 and meets length requirements (max 120m).
  • In a matrix setup, confirm the IGMP Gigabit Switch is functioning correctly and supports IGMP.
  • Verify the TX ID on the transmitter matches the selected input on the receiver (if applicable).
• Poor Picture Quality/Flickering:
  • Ensure the Ethernet cable is of high quality and properly terminated.
  • Ahal bada, murriztu kablearen luzera.
  • Check for electromagnetic interference (EMI) from other devices.
  • Verify that the resolution settings on the source device are compatible with the extender and display.
• IR kontrolak ez du funtzionatzen:
  • Ensure the IR Blaster is correctly positioned over the source device's IR sensor.
  • Ensure the IR Receiver is facing your remote control and connected to the Receiver unit.
  • Check for obstructions between the remote and the IR Receiver.
• RS-232 Control Issues:
  • Verify the RS-232 cable connections and pin assignments.
  • Ensure the baud rate and other serial communication settings match between the control device and the extender.

Zehaztapenak

Image: Physical dimensions of the Transmitter unit.

Mantentzea

• Gorde gailua leku fresko, lehor eta ondo aireztatu batean.
• Saihestu unitatea eguzki-argiaren, tenperatura altuen edo hezetasunaren eraginpean jartzea.
• Ez desmuntatu unitatea. Mantendu konponketa guztiak langile kualifikatuen esku.
• Clean the unit with a soft, dry cloth. Do not use liquid or aerosol cleaners.
• Ensure proper cable management to prevent damage to cables and ports.

Bermea

This SIIG product is covered by a 2 urteko berme mugatua from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage caused by misuse, abuse, unauthorized modifications, or natural disasters. Please retain your proof of purchase for warranty claims.

Bezeroarentzako Arreta

For technical support, product information, or warranty inquiries, please visit the official SIIG website or contact their customer service department. Contact information can typically be found on the product packaging or the SIIG webgunea.