Geekpure 6-Stage Reverse Osmosis RO Drinking Water Filter System with UV Filter-75GPD User Manual

Sarrera

This manual provides detailed instructions for the installation, operation, and maintenance of your Geekpure 6-Stage Reverse Osmosis (RO) Drinking Water Filter System with UV Filter. This system is designed to reduce various contaminants from your drinking water, including arsenic, chlorine, lead, fluoride, mercury, cadmium, and heavy metals, filtering down to 0.0001 micron. The integrated UV filter provides an additional layer of purification without chemical additives.

For optimal performance and longevity of your system, please read these instructions carefully before proceeding with installation or use.

Sistemaren osagaiak

Your Geekpure RO system includes the following components:

• Main System Bracket with Filter Housings
• 6 Filters (PP Sediment, Granular Carbon, Carbon Block, RO Membrane, Post Carbon, UV Filter)
• Banaketa txorrota
• 2.8 litroko biltegiratze-tanga
• Deposituaren Bola Balbula
• Elikatzeko ura desbideratzeko balbula
• Xukatu Zela
• Housing Wrench (2)
• Color-Coded Tubing (BPA-free)
• Konexio azkarreko osagarriak
• Klipak
• Electronic Ballast for UV Filter

Konfigurazioa eta Instalazioa

The Geekpure RO system is designed for under-sink installation. The system comes with high-quality quick connect fittings and color-coded tubing to simplify the installation process. While professional installation is not required, careful attention to detail is crucial to prevent leaks.

Instalazio aurreko egiaztapenak:

• Ziurtatu osagai guztiak daudela eta kaltetu gabe daudela.
• Verify feed water conditions: Pressure 40-100 PSI, Temperature 40-110°F (5-45°C), pH 3.0-11.0, Max TDS 2000 PPM.
• The storage tank is pre-pressurized between 5-7 PSI.

Instalazio Urratsak (Orokorra)view):

1. Unitate Nagusia Muntatu: Secure the main filter unit under your sink in a suitable location.
2. Instalatu txorrota: Drill a hole (if necessary) and install the dispensing faucet on your countertop or sink.
3. Connect Feed Water: Use the feed water diverter valve to connect the system to your cold water supply.
4. Install Drain Saddle: Attach the drain saddle to the drain pipe to dispose of wastewater.
5. Konektatu hodiak: Follow the color-coded tubing guide to connect all filters, the storage tank, faucet, and drain saddle. Ensure tubing is pushed all the way into quick connect fittings and secured with clips.
6. UV Filter Connection: Connect the UV filter and its electronic ballast according to the specific instructions provided for the UV unit.
7. Ihesak egiaztatzea: After completing all connections, slowly turn on the water supply. Carefully check all connections for leaks. It is recommended to wait until the entire system is pressurized (including the storage tank and faucet) and re-check for any leaks before leaving the installation site.
8. Hasierako hustuketa: The first two tanks of water produced should be emptied and not used. It is normal for some black carbon fines to appear in the water during this initial flushing period.

Funtzionamendu-argibideak

Once installed and flushed, your Geekpure RO system will continuously produce purified water. The system has a capacity of 75 gallons per day at 60 PSI.

Uraren ekoizpena:

The system operates automatically. As water is drawn from the faucet, the storage tank pressure drops, and the system begins to produce more purified water to refill the tank. The UV filter operates continuously, 24/7, ensuring consistent water purity.

Wastewater Ratio:

Reverse osmosis is a purification process that produces a small amount of wastewater. For this system, approximately two gallons of wastewater will be produced for every gallon of pure water. This is a normal and necessary part of the RO filtration process.

Uraren kalitatea:

The system significantly reduces Total Dissolved Solids (TDS). You can use a TDS meter to monitor the water quality. Ideal drinking water from RO typically has very low TDS levels.

Mantentzea

Regular maintenance, primarily filter replacement, is essential to ensure the continued high performance and longevity of your Geekpure RO system.

Iragazkiak ordezkatzeko egutegia:

The following table outlines the recommended replacement intervals for each filter stage:

Iragazkiak ordezkatzeko prozedura:

1. Turn off the water supply to the RO system.
2. Close the tank ball valve.
3. Open the RO faucet to relieve pressure.
4. Use the provided housing wrench to unscrew the filter housings.
5. Kendu iragazki zaharrak eta bota itzazu behar bezala.
6. Jarri iragazki berriak, orientazio egokia ziurtatuz.
7. Screw the filter housings back on, hand-tighten, then use the wrench for a quarter turn. Do not overtighten.
8. For the UV filter, carefully replace the UV lamp and quartz sleeve as per the specific UV unit instructions.
9. Slowly turn on the water supply and open the tank ball valve.
10. Check for leaks and perform an initial flush as described in the Setup section.

Arazoak konpontzea

This section addresses common issues you might encounter with your RO system.

No Water Flow or Slow Flow:

• Ur hornidura egiaztatu: Ensure the main water supply and the feed water diverter valve are fully open.
• Deposituaren balbula: Verify the tank ball valve is open.
• Iragazkiak estaliak: Filters, especially the sediment filter and RO membrane, can become clogged over time. Replace filters according to the recommended schedule.
• Uraren presio baxua: Ensure your household water pressure is within the operating range (40-100 PSI).

Isurketak:

• Konexio solteak: Check all quick connect fittings. Ensure tubing is fully inserted and secured with clips.
• O-eraztunak: Inspect O-rings in filter housings for proper seating and damage. Apply food-grade silicone grease if necessary.
• Teflon zinta: For threaded connections, ensure sufficient Teflon tape was used during installation.
• UV ganbera: If leaks occur around the UV chamber, ensure the silicone sleeve and O-rings are correctly positioned and sealed.

Poor Water Taste or Odor:

• Karbono iragazkiak: Granular and Post Carbon filters remove taste and odor. Replace them if taste or odor issues persist.
• RO mintza: A failing RO membrane can lead to poor water quality. Test TDS levels; if high, replace the membrane.
• Hasierako hustuketa: Ensure the initial two tanks of water were fully drained after installation.

UV argia ez dabil:

• Elikatze-iturria: Check if the electronic ballast is plugged in and receiving power.
• UV Lamp: UV lamp has a limited lifespan (9000 hours). Replace it if it has expired or is visibly damaged.
• Ballast Failure: l badaamp is new and power is supplied, the electronic ballast may need replacement.

Zehaztapenak

Bermea eta Laguntza

The Geekpure 6-Stage Reverse Osmosis RO Drinking Water Filter System comes with a 1 urteko fabrikatzailearen bermea. Berme honek ohiko erabileran materialen eta eskulanen akatsak estaltzen ditu.

For technical assistance, troubleshooting, or warranty claims, please refer to the contact information provided with your product packaging or visit the official Geekpure website. When contacting support, please have your model number (RO6-UV) and purchase date available.