1. Sarrera
The AstralPool NA6888 is a sophisticated regulator, controller, and display unit designed for integration with AstralPool heat pump systems. This device provides essential control and monitoring functionalities for your heat pump, ensuring efficient and reliable operation. Please note that this unit is not compatible with remote control systems.
This manual provides detailed instructions for the proper installation, operation, and maintenance of your NA6888 unit. Please read this manual thoroughly before installation and use to ensure safe and optimal performance.
2. Segurtasun informazioa
Beti jarraitu segurtasun-jarraibide hauek unitateari lesioak edo kalteak saihesteko:
- Segurtasun elektrikoa: This unit operates on 220V AC. All electrical connections must be performed by a qualified electrician in accordance with local electrical codes and regulations. Ensure the power supply is disconnected before any installation or maintenance work.
- Ingurumena babestea: The NA6888 unit has an IP65 protection rating, meaning it is protected against dust ingress and low-pressure water jets from any direction. However, avoid direct high-pressure water jets or submersion.
- Erabilera egokia: Use the device only for its intended purpose as a regulator, controller, and display for AstralPool heat pumps. Do not attempt to modify the unit.
- Manipulazioa: Handle the unit with care to avoid physical damage.
3. Produktuaren ezaugarriak
The NA6888 unit offers a range of features for comprehensive heat pump management:
- Kontrol integratua: Combines regulation, control, and display functions in a single compact unit.
- Sentsoreen sarrerak: Supports dedicated inputs for a Temperature Sensor (T1) and a Defrost Sensor (T2).
- Alarma sarrerak: Features three external alarm signal inputs (S1, S2, S3) for enhanced system monitoring.
- Irteera kontrola: Provides control outputs for key heat pump components including Water Pump, Fan, Valve, and Compressor.
- Diseinu iraunkorra: IP65 rated enclosure for protection against dust and water splashes.
3.1. irudia: Aurrealdea view of the NA6888 controller display, showing the digital readout and control buttons.
4. Paketearen edukia
Paketea irekitzean, egiaztatu osagai hauek guztiak daudela:
- 1x NA6888 Regulator-Controller-Display Unit
- 1x Wiring Harness/Cables
- 2x Muntatzeko Klipak
Figure 4.1: Included wiring harness.
Figure 4.2: Mounting clips.
5. Konfigurazioa eta instalazioa
Installation of the NA6888 unit requires careful attention to electrical connections. It is strongly recommended that installation be performed by a qualified and licensed professional.
5.1. Unitatea muntatzea
- Identify a suitable location for the controller, ensuring it is protected from direct sunlight, extreme temperatures, and excessive vibration.
- Cut an appropriate opening in the mounting panel or enclosure, matching the dimensions of the NA6888 unit.
- Insert the NA6888 unit into the opening from the front.
- Secure the unit in place using the provided mounting clips on the sides, ensuring a snug fit.
5.2. Kableatu konexioak
Refer to the wiring diagram printed on the back of the NA6888 unit for precise connection points. Ensure all connections are secure and correctly polarized.
Figure 5.1: NA6888 Wiring Diagram.
Terminalaren deskribapenak:
| Terminala | Deskribapena | Oharrak |
|---|---|---|
| T1 | Tenperatura-sentsorea | Connect the main temperature sensor (NTC=5kΩ/25°C). |
| T2 | Desizozteko sentsorea | Connect the defrost sensor. |
| S1, S2, S3 | External Alarm Signals | Inputs for external alarm triggers. |
| 1, 2 | Potentzia Sarrera | Connect to 220V AC power supply. |
| 6, 7 | Water Pump Output | Control output for the water pump. |
| 8, 9 | Fan Irteera | Control output for the fan. |
| 10, 11 | Balbula Irteera | Control output for the valve. |
| 11, 12 | Konpresorearen irteera | Control output for the compressor. Note shared terminal 11 with Valve. |
After all connections are made, double-check the wiring against the diagram to prevent damage to the unit or connected components.
6. Funtzionamendu-argibideak
Once installed and powered on, the NA6888 display will illuminate, showing current system parameters. The unit features several buttons for navigation and setting adjustments:
- Gora (^) Botoia: Used to increase values or navigate up through menu options.
- Behera (v) Botoia: Used to decrease values or navigate down through menu options.
- SET botoia: Used to enter a menu, confirm a selection, or save a setting.
- M (Menua) botoia: Used to access the main menu or exit a sub-menu.
6.1. Oinarrizko Funtzionamendua
- Piztu: Ensure the unit is correctly wired and power is supplied. The display will show the current temperature or system status.
- Viewing parametroak: Use the Up/Down buttons to cycle through various displayed parameters (e.g., temperature readings from T1/T2, set points, operational status).
- Ezarpenak doitzea:
- Sakatu EZARTU button to enter the setting mode for the currently displayed parameter, or press the M botoia menu nagusira sartzeko.
- Use the Up/Down buttons to adjust the value.
- Sakatu EZARTU again to confirm and save the new value.
- Sakatu M to exit the menu or setting mode.
For detailed programming and advanced settings, refer to the specific programming guide for your AstralPool heat pump model, as the NA6888 acts as the interface for these settings.
7. Mantentzea
The NA6888 unit is designed for low maintenance. Regular checks can help ensure its longevity and proper function:
- Garbiketa: Aldian-aldian garbitu pantaila eta casing bigun batekin, damp oihalik. Ez erabili garbitzaile edo disolbatzaile urratzailerik. Ziurtatu likidorik ez dela sartzen unitatean.
- Konexioaren egiaztapena: Annually, or if issues arise, have a qualified technician check all electrical connections for tightness and signs of corrosion.
- Ingurumen-baldintzak: Ensure the unit remains within its specified operating environment (temperature, humidity) and that its IP65 rating is not compromised by physical damage.
8. Arazoak
If you encounter issues with your NA6888 unit, consider the following common troubleshooting steps. For complex problems, always consult a qualified technician.
| Arazoa | Kausa posiblea | Irtenbidea |
|---|---|---|
| Pantaila hutsik dago | No power supply; Loose connection; Unit failure. | Check power source (220V AC). Verify wiring connections. If power is present and connections are secure, the unit may require replacement. |
| Tenperaturaren irakurketa okerra | Faulty sensor (T1 or T2); Loose sensor connection. | Check sensor wiring. Test sensor resistance (NTC=5kΩ/25°C). Replace sensor if faulty. |
| Outputs (Pump, Fan, etc.) not activating | Incorrect settings; Wiring issue; Component failure. | Verify controller settings. Check wiring to the respective component. Test the component itself. |
| External alarm not registering | Incorrect wiring to S1/S2/S3; Faulty external alarm device. | Check wiring to alarm inputs. Test the external alarm device. |
If troubleshooting steps do not resolve the issue, contact AstralPool customer support or a certified service technician. Information regarding spare parts availability is not provided.
9. Zehaztapenak
| Parametroa | Balioa |
|---|---|
| Modelo zenbakia | NA6888 |
| Marka | AstralPool |
| Elikatze Hornidura | 220V AC, 2A max |
| Tenperatura-sentsorearen sarrera | T1 (NTC=5kΩ/25°C) |
| Defrost Sensor Input | T2 |
| Kanpoko Alarma Sarrerak | S1, S2, S3 |
| Kontrol Irteerak | Water Pump, Fan, Valve, Compressor |
| Babes-balorazioa | IP65 |
| Instalazio Kategoria | CAT II |
| ASIN | B07XGCN44T |
| Eskuragarri dagoen lehen data | 21ko ekainaren 2021a |
10. Bermea eta Laguntza
Specific warranty terms for the NA6888 unit are typically provided at the point of purchase or can be obtained directly from AstralPool. Please retain your proof of purchase for warranty claims.
For technical support, service, or inquiries regarding spare parts, please contact AstralPool customer service or your authorized dealer. Contact information can usually be found on the AstralPool official webgunean edo zure erosketa-dokumentazioan.
