Sarrera
This manual provides detailed instructions for the DKARDU DC 5V-12V Mini Microphone Amplifier Board. This module is designed to amplify audio signals from various microphone types, including electret, condenser, and moving coil microphones, for output to speakers. It is suitable for a wide range of audio projects and applications.
Irudia: Gainetikview of the DKARDU Mini Microphone Amplifier Board kit, including two amplifier modules, two electret microphones, and two power cables.
Kutxan dagoena
Paketeak osagai hauek ditu:
- 2 x DC 5V-12V Micro Electret AmpLider Oholak
- 2 x Electret Microphones
- 2 x DC Female Power Pigtail Cables
Zehaztapenak
Zehaztapen tekniko zehatzak ampmoduluaren modulua:
| Parametroa | Balioa |
|---|---|
| Bolumen eragileatage | 5V-12V DC (Voltage below 5V will significantly reduce sound; do not exceed 15V) |
| Funtzionamendu Korrontea | 1mA (static) ~ 150mA (max) |
| Output Speaker Impedance | 4 Ω - 32 Ω (Higher impedance results in higher efficiency) |
| Supported Speaker Power | 0.5W-25W (Any power speaker can be used, volume is not directly proportional to speaker power, as long as it's greater than amplifier output rating) |
| Irteerako potentzia maximoa | 750mW |
| Sarrera euskarria | Electret microphone, condenser microphone, moving coil microphone, audio signal |
| Neurriak (LxWxH) | 20 x 12 x 6mm / 0.79 x 0.47 x 0.23 hazbeteko |
Irudia: Xehetasun handikoa view ren amplifier board highlighting its key parameters.
Image: Dimensions of the amplifier board, showing its compact size.
Konfigurazioa
Follow these steps to correctly set up your ampbizigarri taula:
- Mikrofonoa konektatu: Use a shielded cable to connect the electret microphone to the 'IN' and 'GND' terminals of the amplifier board. Pay close attention to the polarity of the electret microphone; incorrect polarity will result in very low or no sound.
- Konektatu bozgorailua: Connect your speaker to the 'OUT' terminals of the amplifier board. Ensure the speaker is positioned away from the microphone to prevent self-excited noise (feedback).
- Konektatu energia: Connect a DC power supply (5V-12V) to the positive and negative terminals of the ampargitzaile taula. WARNING: Do not reverse the polarity of the power supply, as this will damage the module.
Image: A clear wiring diagram illustrating how to connect the DC power supply, microphone, and speaker to the ampargitzaile taula.
Funtzionamendu-argibideak
Once properly set up, the amplifier board will begin to amplify the audio signal from the connected microphone. The module supports various microphone types and can be integrated into different audio systems.
- Bolumenaren doikuntza: The board features a small potentiometer (labeled 'VOL') for adjusting the output volume. Use a small screwdriver or appropriate tool to carefully turn the potentiometer to achieve the desired volume level.
- Sarreraren bateragarritasuna: The amplifier is designed to work with electret, condenser, and moving coil microphones, as well as general audio signals.
Irudia: The amplifier board, illustrating its compatibility with electret, microphone, condenser microphone, moving coil microphone, and general audio signals.
Irudia: Adibamples of different applications and wiring configurations for the amplifier board, demonstrating its versatility.
Mantentzea
To ensure the longevity and optimal performance of your DKARDU Mini Microphone Amplifier Board, consider the following maintenance guidelines:
- Mantendu lehorra: Protect the module from moisture and liquids, as water can cause short circuits and damage components.
- Garbitu astiro-astiro: If cleaning is necessary, use a soft, dry cloth. Avoid using harsh chemicals or abrasive materials.
- Kontuz maneiatu: The board contains delicate electronic components. Avoid dropping or subjecting it to strong impacts.
- Biltegiratze egokia: When not in use, store the module in a cool, dry place, away from direct sunlight and extreme temperatures.
Arazoak konpontzea
Zurekin arazoak badituzu amplifier board, refer to the following common problems and solutions:
- Very Little or No Sound:
- Check the polarity of the electret microphone connection to the 'IN' and 'GND' terminals. Reversing the polarity will significantly reduce or eliminate sound.
- Ziurtatu elikadura hornidura boltage is within the 5V-12V range. Voltage below 5V will result in significantly reduced sound.
- Verify all connections are secure and correct according to the wiring diagram.
- Self-Excited Noise (Feedback):
- Ensure the speaker is positioned sufficiently far away from the microphone to prevent audio feedback.
- Check for proper shielding of the microphone cable.
- Module Not Functioning / Damaged:
- Verify that the DC power supply polarity is correct. Reversing the positive and negative connections will burn out the module.
- Ziurtatu sarrera voltage-k ez du 15V gainditzen.
Image: Important notes for the amplifier board, emphasizing correct wiring and power supply to prevent damage and ensure proper function.
Bermea eta Laguntza
For warranty information and customer support, please refer to the documentation provided with your purchase or contact DKARDU customer service through the retailer where the product was acquired. Keep your proof of purchase for any warranty claims.
