FLIPSKY VX3 Urruneko Kontrolagailu Guztiz Iragazgaitza Erabiltzailearen Eskuliburua

1. Sarrera

The FLIPSKY VX3 is a fully waterproof remote controller designed for Efoil, Esurf, and ESK8 applications. It features a 1.6-inch clear display, wireless magnetic charging, and compatibility with FLIPSKY FSESC and other VESC/Non-VESC systems. This manual provides essential information for the safe and effective use of your VX3 remote controller.

2. Segurtasun informazioa

Please read and understand all safety instructions before using the FLIPSKY VX3 remote controller. Failure to follow these instructions may result in injury or damage to the product.

• Uraren esposizioa: While the VX3 is IP67 waterproof, always ensure the charging port is clean and dry before charging. After use in saltwater, rinse the remote thoroughly with fresh water for at least one minute to prevent salt residue buildup and corrosion.
• Bateriaren segurtasuna: The remote contains a Lithium-Ion battery. Do not attempt to open, puncture, or expose the battery to extreme temperatures. Use only the provided wireless magnetic charger.
• Eragiketa-ingurunea: Operate the remote responsibly and be aware of your surroundings. Always maintain a safe distance from other people and objects.
• Firmware eguneraketak: Only perform firmware updates using official FLIPSKY tools and instructions. Incorrect updates can damage the device.
• Haurrak: Mantendu gailua haurren eskura.

3. Paketearen edukia

Egiaztatu behean zerrendatutako elementu guztiak zure paketean sartuta daudela:

Image: Contents of the FLIPSKY VX3 Remote Controller package.

• FLIPSKY VX3 Remote Controller
• Haririk gabeko kargagailu magnetikoa
• USB kargatzeko kablea
• Hargailuen modulua
• Connection Cables (PPM/UART)
• Argibide eskuliburua

4. Produktua amaitu daview

The FLIPSKY VX3 remote controller is designed for intuitive control and comprehensive data display.

Irudia: Aurrealdea view of the VX3 remote controller highlighting the display screen.

Ezaugarri nagusiak:

• 1.6 hazbeteko pantaila: Provides real-time telemetry data, GPS information, motor power, MOS tube temperature, and throttle progress.
• Diseinu ergonomikoa: Helduleku erosoa erabilera luzerako.
• Control Lever: For throttle and braking.
• Funtzio-botoiak: For mode switching and menu navigation.

Irudia: Atzealdea view of the VX3 remote controller.

5. Konfigurazioa

5.1 Charging the Remote

The VX3 remote controller features wireless magnetic charging.

Image: VX3 remote controller alongside its wireless magnetic charging pad and USB cable.

1. Connect the USB charging cable to the wireless magnetic charger and a suitable USB power source (e.g., wall adapter, computer USB port).
2. Place the VX3 remote controller onto the magnetic charging pad. Ensure proper alignment for the charging indicator to activate.
3. The remote's display will indicate charging status. A full charge typically takes several hours.

Oharra: Always ensure the remote and charging pad are dry before charging to prevent damage.

5.2 Connecting the Receiver to ESC

The VX3 remote supports both UART and PPM control modes. Choose the appropriate connection method based on your Electronic Speed Controller (ESC).

UART Control Mode

This mode is suitable for FLIPSKY FSESC and other VESC-based ESCs, offering advanced telemetry data and forward/reverse switching functionality.

Image: Diagram illustrating the UART control mode wiring for the receiver.

Connect the receiver to your VESC-based ESC using the UART port as shown in the diagram. Ensure correct pin alignment for VESC RX, VESC TX, GND, and 5V.

PPM Kontrol Modua

This mode is applicable to all ESCs and provides basic throttle control without positive and reverse switching functionality.

Image: Diagram illustrating the PPM control mode wiring for the receiver.

Connect the receiver to your ESC using either the PPM1 or PPM2 port as shown. For dual channel connection, use both PPM1 and PPM2 for two motors/ESCs.

6. Funtzionamendu-argibideak

6.2 Bistaratu informazioa

The 1.6-inch display provides comprehensive real-time data:

Image: Screen display introduction for ESK8 mode, detailing data points like speed, mileage, current, motor power, and temperature.

Image: Screen display introduction for Esurf mode, detailing data points including GPS signal, speed, mileage, current, motor power, and temperature.

• Receiver Signal (RU/RP): Indicates connection strength.
• Urruneko bateria: Current battery level of the remote.
• Esk8/Esurf Battery: Battery level of the connected device.
• GPS Signal (G): Indicates GPS reception status (Esurf mode).
• Real-time Speed: Current speed in km/h or mph.
• Kilometro bakarra: Distance traveled during the current session.
• ESC Real-time Current: Current draw from the ESC.
• Motor potentzia: Real-time motor power output.
• ESC Temperature: Real-time temperature of the MOS tube on the ESC.
• Putter Throttle Percentage: Visual representation of the throttle input.
• Speed Mode (H/M/L): Current speed limit setting (High, Medium, Low).

7. Mantentzea

• Garbiketa: After each use, especially in saltwater environments, wash or soak the VX3 remote in fresh water for at least one minute. This helps reduce salt residue and extends the life of the device. Ensure the remote is completely dry before storing or charging.
• Biltegiratzea: Gorde urrutiko agintea leku fresko eta lehor batean, eguzki-argitik eta muturreko tenperaturetatik babestuta.
• Bateria zaintzea: For long-term storage, charge the remote's battery to approximately 50-60%. Avoid fully discharging the battery for extended periods.

8. Arazoak

• Remote Not Turning On: Ensure the battery is charged. Place it on the wireless charger to confirm charging status.
• No Connection to ESC: Check that the receiver is correctly wired to the ESC (UART or PPM). Ensure both the remote and ESC are powered on. Re-pair the remote and receiver if necessary (refer to pairing instructions in the full manual, if available).
• Inaccurate Speed/Telemetry: Verify that the remote is correctly configured for your wheel size/motor parameters (if applicable). Ensure GPS signal is strong in Esurf mode.
• Kargatzeko arazoak: Check the USB cable and power source. Ensure the remote is properly aligned on the magnetic charging pad.
• Pantaila ez dabil: If the display is blank or frozen, try restarting the remote. If the issue persists, contact FLIPSKY support.

9. Zehaztapenak

10. Bermea eta Laguntza

FLIPSKY products are designed and manufactured to the highest quality standards. For warranty information and technical support, please refer to the official FLIPSKY webwebgunera edo jarri harremanetan zure baimendutako saltzailearekin. Gorde erosketa-agiria erosketaren frogagiri gisa berme-erreklamazioetarako.

Laguntza gehiago lortzeko, mesedez bisitatu: www.flipsky.net