LEDONE 8FT LED Vapor Tight Light Instruction Manual

1. Sarrera

This manual provides detailed instructions for the safe installation, operation, and maintenance of your LEDONE 8FT LED Vapor Tight Light. Please read this manual thoroughly before installation and retain it for future reference. This fixture is designed for demanding environments requiring high resistance to water, dust, and corrosion, such as parking garages, car washes, cold storage, and industrial facilities.

2. Segurtasun informazioa

WARNING: Risk of electric shock. Disconnect power before installation or servicing.

• Installation must be performed by a qualified electrician in accordance with the National Electrical Code (NEC) and local codes.
• Ziurtatu hornidura boltage is compatible with the fixture's requirements (120-277Vac).
• Ez manipulatu energiaz betetako tresnak esku bustiekin edo gainean busti edo lehorrean zutik zauden bitartean.amp gainazalak.
• Ez saiatu aparatua aldatzen edo desmuntatzen. Barruan ez dago erabiltzaileak konpondu dezakeen piezarik.
• Erabili babes pertsonaleko ekipamendu (BPE) egokia instalazioan zehar.
• Ensure the fixture is securely mounted to prevent falling.

3. Paketearen edukia

Instalazioarekin jarraitu aurretik, egiaztatu osagai guztiak daudela eta kalterik gabe daudela.

• LEDONE 8FT LED Vapor Tight Light Fixture
• Mounting Hardware (clips, screws, anchors)
• Argibide eskuliburua (dokumentu hau)

4. Konfigurazioa eta instalazioa

4.1. Aurreinstalazioa

1. Itzali energia: Locate the circuit breaker or fuse box and turn off the power supply to the installation area. Verify power is off using a voltage probatzailea.
2. Desegin: Carefully remove the fixture from its packaging. Inspect for any shipping damage.
3. Hautatu Wattage and Color Temperature (CCT): Before mounting, adjust the wattage and CCT switches located on the fixture. These switches allow you to select between 60W, 80W, or 100W and 3500K, 4000K, or 5000K. Make your selection based on your lighting requirements.

Image: Product dimensions and location of wattage/CCT selection switches.

4.2. Elementua muntatzea

The fixture is designed for surface mounting. Use the provided mounting clips and hardware.

1. Mark the desired mounting locations on the ceiling or wall. Ensure the marks are level and spaced appropriately for the fixture's length.
2. Drill pilot holes at the marked locations. Insert wall anchors if mounting into drywall or masonry.
3. Secure the mounting clips to the surface using the provided screws.
4. Snap the LED vapor tight fixture into the mounted clips, ensuring it is firmly seated.

Irudia: Adibample of surface mounting in a facility.

Image: Detail of the linkable design feature.

4.3. Kableatu elektrikoa

This fixture supports 0-10V dimming. Follow the wiring diagram below and local electrical codes.

• Konektatu Beltza kablea aparatutik gailuaraino Lerroa (L) wire from the power supply.
• Konektatu Zuria kablea aparatutik gailuaraino Neutroa (N) wire from the power supply.
• Konektatu Berdea kablea aparatutik gailuaraino Lurra (GND) wire from the power supply.
• 0-10V-ko argiztapena erregulatzeko: Konektatu Morea kablea aparatutik gailuaraino Dim+ wire from the 0-10V dimmer. Connect the Arrosa/Grisa kablea aparatutik gailuaraino Dim wire from the 0-10V dimmer.
• Ziurtatu konexio guztiak ondo finkatuta daudela kable-konektore egokiak erabiliz.

Note: If 0-10V dimming is not used, cap the purple and pink/gray wires individually with wire nuts.

5. Funtzionamendu-argibideak

1. Piztu: Once installation and wiring are complete, restore power to the circuit at the breaker or fuse box. The fixture should illuminate.
2. dimming: If connected to a compatible 0-10V dimmer, adjust the dimmer control to achieve the desired light output level.
3. Wattage and CCT Adjustment: Wattage and CCT are set via internal switches during installation. These are not typically adjusted during normal operation. If changes are needed, disconnect power before accessing the switches.

6. Mantentzea

The LEDONE Vapor Tight Light is designed for long-term, low-maintenance operation. Regular cleaning can help maintain optimal light output.

• Garbiketa: Deskonektatu korrontea garbitu aurretik. Erabili eskuila leun eta lehorra.amp cloth with a mild, non-abrasive cleaner to wipe the exterior of the fixture. Do not use harsh chemicals or abrasive pads, as these can damage the finish or lens.
• Ikuskapena: Periodically inspect the fixture and mounting hardware for any signs of damage, loose connections, or wear. Address any issues promptly.
• Erabiltzaileak ez du zerbitzurik gabeko piezarik: The LED light source and driver are integrated components. Do not attempt to open or repair the fixture. Contact qualified personnel for any issues beyond basic cleaning and inspection.

Image: The IP65 waterproof rating ensures durability in wet conditions.

7. Arazoak

Before performing any troubleshooting, ensure power is disconnected at the circuit breaker.

8. Zehaztapenak

Image: Key features and certifications of the LEDONE Vapor Tight Light.

9. Bermearen informazioa

LEDONE products are manufactured to high quality standards. This product comes with a standard manufacturer's warranty. Please refer to the product packaging or the official LEDONE website for specific warranty terms and conditions. Keep your proof of purchase for warranty claims.

10. Bezeroarentzako arreta

If you have any questions, require technical assistance, or need to report an issue, please contact LEDONE customer support:

• Webgunea: Visit the LEDONE Store on Amazon (for general inquiries)
• Posta elektronikoa: Kontsultatu produktuaren ontziratzea edo agiri ofiziala website for direct support email.
• Telefonoa: Kontsultatu produktuaren ontziratzea edo agiri ofiziala website for direct support phone number.

Please have your product model number (8FT LED Vapor Tight Light) and proof of purchase ready when contacting support.