HANMATEK HO51 Portable 3-in-1 Oscilloscope, Multimeter, and Waveform Generator User Manual

1. Sarrera

The HANMATEK HO51 is a versatile, portable 3-in-1 device that integrates the functions of a digital oscilloscope, a multimeter, and a waveform generator. Designed for electronic troubleshooting, testing, and educational purposes, it offers a compact solution for various measurement needs. Its user-friendly interface and robust design make it suitable for both beginners and experienced professionals.

Ezaugarri nagusiak:

• 3-en-1 funtzionaltasuna: Combines an oscilloscope, multimeter, and waveform generator in a single compact unit.
• Osziloskopioa: 50 MHz bandwidth and 250 MS/s real-time sampling rate for precise waveform analysis.
• Multimetroa: Accurate measurements of voltage, current, resistance, capacitance, continuity, and diode tests.
• Uhin-formaren sorgailua: Generates sine, square, triangle, and custom waveforms up to 1 MHz.
• Diseinu eramangarria: Lightweight and compact (198mm x 100mm x 39mm, 0.5 kg) for easy transport and field use.
• Pantaila: 3.5-inch color screen with an intuitive interface.
• PC Softwarearen bateragarritasuna: USB connectivity for data transfer and advanced control.
• Potentzia: Operates on battery or via USB power.

Image 1.1: The HANMATEK HO51's integrated Oscilloscope, Multimeter, and Waveform Generator functions.

2. Segurtasun informazioa

Mesedez, irakurri arretaz segurtasun-jarraibide guztiak gailua erabili aurretik. Argibide hauek ez jarraitzen badituzu, deskarga elektrikoak, sua edo gailuari kalteak eragin ditzake.

• Ez erabili gailua hondatuta dagoela edo behar bezala funtzionatzen ez badu.
• Ensure proper probe connections and settings before taking measurements.
• Ez gainditu bolumenaren sarrera-balio maximoaktage eta egungoa.
• Use only the accessories provided or approved by HANMATEK.
• Saihestu gailua heze edo lehorrean erabiltzea.amp baldintzak.
• Disconnect power from the circuit under test before connecting or disconnecting probes.
• Beti bete tokiko eta nazioko segurtasun-kodeak.

3. Paketearen edukia

Egiaztatu behean zerrendatutako elementu guztiak zure paketean sartuta daudela. Elementuren bat falta bada edo hondatuta badago, jarri harremanetan zure saltzailearekin.

• HANMATEK HO51 Device
• USB kablea (C mota)
• Osziloskopioko zunda pasiboa
• Multimeter Test Leads
• Hasierako gida azkarra
• Probe Calibration Tool
• Elikatze-moldagailua
• Karkasa biguna

Image 3.1: HANMATEK HO51 device and included accessories.

4. Produktua amaitu daview

The HANMATEK HO51 features a clear layout for easy operation. Familiarize yourself with the buttons, connectors, and display area.

4.1 Aurrealdeko panelaren kontrolak eta pantaila

Image 4.1: Front panel layout and controls of the HANMATEK HO51.

• Bistaratzeko eremua: 3.5-inch color screen for waveform, measurement data, and menu display.
• F1-F4 Keys: Multi-function keys, their purpose changes based on the current menu.
• Modu-gakoa: Osziloskopio, multimetro eta uhin-formako sorgailu moduen artean aldatzen du.
• CH Key: Channel selection (if applicable) or related settings.
• HOR Key: Horizontal scale adjustment for oscilloscope.
• Sistemaren gakoa: Accesses system settings, including language selection.
• Gorde gakoa: Saves current waveform data or measurement results.
• Trig/Δ Key: Trigger menu for oscilloscope or relative value key for multimeter.
• Auto tekla: Automatic setting for oscilloscope or automatic range key for multimeter.
• Measure Range Key: Measurement menu for oscilloscope or range key for multimeter.
• Pizteko etengailuaren tekla: Gailua pizten edo itzaltzen du.
• Erreproduzitu/Pausatu tekla: Stops/runs oscilloscope acquisition or holds value for multimeter.
• Nabigazio teklak: Gora, Behera, Ezkerra, Eskuina menuan nabigatzeko eta parametroak doitzeko.
• Multimeter Input Ports: A, mA, COM, QVC for connecting multimeter test leads.

4.2 Side and Bottom Connectors

4.2 irudia: Albokoa view showing Type-C charging port and rear stand.

• C motako kargatzeko ataka: Located on the side for charging the internal battery and USB communication with a PC.
• Probe Compensation / Signal Generator Output Connector: Located on the top side, provides a 2.5V/1KHz square wave signal for probe calibration and serves as the waveform generator output.
• Measured Signal Input Connector (BNC): Located on the bottom for connecting the oscilloscope probe.
• Parentesia: An expandable stand on the back allows for convenient viewangeluak.

5. Konfigurazioa

5.1 Hasierako karga

Before first use, fully charge the device using the provided USB Type-C cable and power adapter. The charging indicator will show the charging status.

5.2 Piztu/Itzali

Eduki sakatuta Pizteko etengailuaren tekla (usually marked with a power symbol) to turn the device on or off.

5.3 Hizkuntza hautatzea

Upon first startup, the device may be in a default language. To change the language:

1. Sakatu Sistema giltza.
2. Navigate to the language settings (often labeled F2 or similar).
3. Select your desired language (e.g., English) using the navigation keys and confirm.

5.4 Oscilloscope Probe Calibration

For accurate oscilloscope measurements, calibrate the passive probe before use:

1. Connect the oscilloscope probe to the BNC input connector on the bottom of the device.
2. Connect the probe tip to the probe compensation/signal generator output connector (1KHz square wave) on the top side of the device.
3. Enter Oscilloscope mode (if not already there) and adjust the vertical and horizontal scales to view the square wave.
4. Using the small calibration tool, adjust the screw on the probe connector until the square wave displayed on the screen has flat tops and bottoms with sharp corners, indicating proper compensation.

6. Funtzionamendu-argibideak

6.1 Aldaketa moduak

Sakatu Modua key to cycle between Oscilloscope, Multimeter, and Waveform Generator functions.

6.2 Oscilloscope Operation

In Oscilloscope mode, the device displays waveforms over time. Use the following controls:

• Eskala bertikala (Volt/Div): Adjust using the navigation keys (Up/Down) when the vertical scale is highlighted.
• Eskala horizontala (Denbora/Division): Sakatu AURRETIK and then use navigation keys (Left/Right) to adjust.
• Trigger ezarpenak: Sakatu Trigonometria/Δ to access trigger menu. Adjust trigger level, mode (Auto, Normal, Single), and type (rising/falling edge).
• Konfigurazio automatikoa: Sakatu Autoa for automatic waveform scaling and positioning.
• Korrika/Gelditu: Sakatu Erreproduzitu/Pausatu key to start or stop waveform acquisition.

6.3 Multimetroaren funtzionamendua

In Multimeter mode, the device performs various electrical measurements. Connect the multimeter test leads to the appropriate input ports (A, mA, COM, QVC).

• Funtzioa hautatzea: Use the F1-F4 keys or navigation keys to select measurement functions (Voltage, Current, Resistance, Capacitance, Continuity, Diode).
• Barrutia hautatzea: Sakatu Neurketa-eremua to manually select the measurement range, or use Autoa for automatic ranging.
• Jarraitasun proba: Connect leads across a circuit. An audible tone indicates continuity. Note that some users have reported a slight delay in response for continuity tests.
• Diodo proba: Connect leads across a diode to measure its forward voltage tanta.

6.4 Waveform Generator Operation

In Waveform Generator mode, the device outputs various signals from the probe compensation/signal generator output connector.

• Uhin forma mota: Use the F1-F4 keys or navigation keys to select the desired waveform (Sine, Square, Triangle, Pulse).
• Maiztasun Doikuntza: Adjust the output frequency using the navigation keys.
• AmpAltitudearen doikuntza: Egokitu irteera amplitude (1Vpp or 2.5Vpp) using the navigation keys.

6.5 PC softwarearen konexioa

Connect the HO51 to a computer via the USB Type-C port. Compatible PC software allows for data transfer, waveform analysis, and remote control of the device. Refer to the software's documentation for detailed instructions.

Image 6.1: HANMATEK HO51 connected to a PC for data export and analysis.

7. Mantentzea

Proper maintenance ensures the longevity and accuracy of your HANMATEK HO51.

• Garbiketa: Erabili biguna, damp cloth to clean the device. Do not use abrasive cleaners or solvents. Ensure the device is powered off and disconnected from any power source before cleaning.
• Biltegiratzea: Store the device in a cool, dry place, away from direct sunlight and extreme temperatures. Use the provided carrying case for protection.
• Bateria zaintzea: Bateriaren iraupen optimoa lortzeko, saihestu bateria guztiz deskargatzea maiz. Denbora luzez gordetzen baduzu, kargatu bateria % 50 inguru hilabete batzuk behin.
• Firmware eguneraketak: Periodically check the HANMATEK official webwebgunea eskuragarri dauden firmware eguneratzeetarako, errendimendu optimoa eta funtzio berrietarako sarbidea bermatzeko.

8. Arazoak

If you encounter issues with your HANMATEK HO51, refer to the following common problems and solutions.

• Gailua ez da pizten:
  • Ensure the battery is charged. Connect the device to a power source using the USB-C cable and adapter.
  • Eduki sakatuta pizteko botoia segundo batzuetan.
• Ez da uhin-formarik bistaratzen osziloskopio moduan:
  • Check if the probe is correctly connected to the BNC input.
  • Verify the probe is properly calibrated.
  • Adjust the vertical (Volts/Div) and horizontal (Time/Div) scales.
  • Check trigger settings; try setting the trigger mode to 'Auto' or adjusting the trigger level.
  • Ensure the 'Run' state is active (not paused).
• Multimeter readings are inaccurate or slow:
  • Ensure test leads are securely connected to the correct input ports.
  • Verify the correct measurement function and range are selected.
  • For continuity tests, allow a moment for the device to register the connection, as some users have noted a slight delay.
  • Consider performing a factory reset via the System menu if persistent issues occur.
• Waveform generator output is incorrect:
  • Ensure the output is connected to the correct port.
  • Verify the selected waveform type, frequency, and amplitude ezarpenak.

9. Zehaztapenak

Detailed technical specifications for the HANMATEK HO51 device.

9.1 Oscilloscope Specifications

9.2 Multimetroaren zehaztapenak

9.3 Waveform Generator Specifications

9.4 Zehaztapen orokorrak

10. Bermea eta Laguntza

For warranty information, technical support, or service inquiries, please refer to the documentation included with your product or contact HANMATEK customer service directly. You may also visit the product page on Amazon for additional support resources or to contact the seller.

Amazonen produktuen orria: HANMATEK HO51 on Amazon.com.be