1. Sarrera
This manual provides essential information for the safe and efficient installation, operation, and maintenance of your EARU Electric 3-Phase Auto Transfer Switch (ATS) - 440V 63A. Please read this manual thoroughly before installation and operation to ensure proper functionality and to prevent damage or injury.
The ATS is designed to provide uninterrupted power by automatically transferring loads between phases in a three-phase supply system. It features intelligent monitoring and protection against phase failure, over/under voltage, and overcurrent conditions, ensuring the stability and safety of connected equipment.
2. Segurtasun informazioa
OHARRA: Deskarga elektrikoaren arriskua. Instalazioa eta mantentze-lanak langile kualifikatuek bakarrik egin behar dituzte.
- Always disconnect power before installing or servicing the ATS.
- Ziurtatu kableatu guztiak tokiko eta estatuko arau elektrikoen araberakoak direla.
- Egiaztatu liburu zuzenatage and current ratings before connecting the device.
- Ez erabili gailua hondatuta dagoela dirudienean.
- Mantendu haurrak tresna elektrikoetatik urrun.
3. Produktua amaitu daview
The EARU Electric 3-Phase ATS is an intelligent device that continuously monitors your three-phase power supply. It automatically switches single-phase loads to a healthy phase in case of a phase failure or imbalance, ensuring continuous operation of critical equipment.
3.1. Paketearen edukia
- 1 x EARU Electric 3-Phase Auto Transfer Switch (ATS)
3.2. Front Panel and Indicators
Irudiaren deskribapena: The front panel of the ATS features a digital display showing voltage for L1, L2, L3 phases and current for L1. Below the display are indicators for Power, Over-voltage (>V), Under-voltage (<V), and Over-current (>I). Control buttons include 'SET' (Menu key), 'Digit+/Up', 'Digit-/Down', and 'Manual ON/OFF' (Power button).
The digital display provides real-time voltage readings for each phase (L1, L2, L3) and the current for L1. Status indicators alert you to the operational state and any detected faults:
- Potentzia: Output indication.
- >V: Bolumen gehiegitage adierazlea.
- <V: Bolumen azpikoatage adierazlea.
- > ni: Over-current indication.
Control buttons allow for parameter settings and manual operation:
- SET: Menu key for accessing settings.
- Digit+/Up: Increases value or navigates up in menus.
- Digit-/Down: Decreases value or navigates down in menus.
- Eskuzko ON/OFF: Power button for manual control.
4. Konfigurazioa eta instalazioa
The ATS is designed for standard DIN rail mounting. Ensure sufficient space for ventilation and wiring connections.
4.1. Kableatuen Diagrama
Irudiaren deskribapena: A detailed wiring diagram illustrates the connection points for the ATS. The top terminals are labeled 'IN' with connections for N, L1, L2, L3. The bottom terminals are labeled 'OUT' with connections for N and L1. The diagram shows how to connect the three-phase input to the ATS and how a single-phase load (L1 and N) is connected to the output, with internal connections for phase monitoring and switching.
Follow the wiring diagram carefully. Incorrect wiring can lead to device malfunction or electrical hazards.
- Connect the incoming three-phase power supply (N, L1, L2, L3) to the 'IN' terminals.
- Connect the single-phase load (N, L1) to the 'OUT' terminals. The ATS will manage the phase transfer for the L1 output.
- Ensure all connections are secure and tightened to prevent loose contacts and overheating.
4.2. Hasierako piztea
After completing the wiring, restore power to the system. The ATS will power on and begin monitoring the phases. The digital display will show the current voltage readings for each phase. If all phases are stable and within acceptable limits, the ATS will provide power to the output.
5. Funtzionamendu-argibideak
The ATS operates automatically, but you can adjust its protection parameters to suit your specific requirements.
5.1. Pantaila eta adierazleak ulertzea
The digital display continuously shows the real-time voltage of each phase (L1, L2, L3) and the current on L1. The indicator lights provide quick visual feedback on the device's status and any detected anomalies.
Irudiaren deskribapena: Gertu bat view of the ATS digital display. It shows '220V' for L1, L2, and L3, and '63.0A' for L1 current. Below these readings are small indicator icons for Power, >V (Over-voltage), <V (Under-voltage), and >I (Over-current).
5.2. Adjusting Protection Parameters
Use the 'SET' button to enter the parameter setting mode. Use the 'Digit+/Up' and 'Digit-/Down' buttons to navigate through settings and adjust values. Press 'SET' again to confirm and save changes.
| Parametroa | Ezarpen-barrutia | Ezarpen lehenetsia |
|---|---|---|
| Over Current Protection Setting Range | 1-63A/100A | 30A |
| Continuous Over Current Protection Times | 0-20 aldiz | OFF |
| Voltage Protection Setting Range | 230-300V | 270V |
| Voltage Protection Recover Setting Range | 225-295V | 265V |
| Vol. Peantage Protection Setting Range | 140-210V | 170V |
| Vol. Peantage Protection Recover Setting Range | 145-215V | 175V |
| liburukiatage & Current Protection Recover Delay | 1-500 hamarkada | 30 s |
5.3. Automatic Phase Transfer
The ATS automatically monitors the three input phases (L1, L2, L3). If a phase failure or significant voltage imbalance (over/under voltage) is detected on the currently supplying phase, the device will automatically transfer the single-phase output load to a healthy, stable phase within the same supply. This process is designed to be seamless and rapid, minimizing power interruption to connected equipment.
5.4. Automatic Recovery
Once the primary phase recovers and stabilizes, the ATS will intelligently switch the load back to the primary source, ensuring optimal power distribution and preventing equipment damage from unstable power. The recovery delay can be configured as per your operational needs.
6. Mantentzea
The EARU Electric ATS is designed for minimal maintenance. However, periodic checks are recommended to ensure optimal performance and longevity.
- Garbiketa: Mantendu gailua garbi eta hautsik eta hondakinik gabe. Erabili zapi lehor eta leun bat garbitzeko. Ez erabili garbitzaile likidorik.
- Konexioaren egiaztapenak: Periodically inspect all wiring connections to ensure they remain tight and free from corrosion.
- Ingurumen-baldintzak: Ziurtatu funtzionamendu-ingurunea zehaztutako tenperatura eta hezetasun tarteen barruan mantentzen dela.
7. Arazoak
If you encounter issues with your ATS, refer to the following common problems and solutions:
| Arazoa | Kausa posiblea | Irtenbidea |
|---|---|---|
| Potentzia irteerarik ez | No input power; all phases unstable; device in fault state. | Check incoming power supply. Verify all phases are stable. Check fault indicators. |
| ">V" or "<V" indicator lit | Bolumen gehiegitage edo beheko boltage detected on a phase. | Egiaztatu sarrera bolumenatage stability. The ATS will automatically transfer if another phase is healthy. |
| ">I" indicator lit | Over-current detected on the output. | Reduce load on the output. Check for short circuits in the connected equipment. |
| Device not transferring phases | No healthy alternative phase available; transfer delay setting too long. | Ensure at least one healthy phase is present. Check and adjust the transfer delay settings. |
| Pantaila digitala ez da funtzionatzen | No power to the device; internal fault. | Check power supply. If power is present and display is off, contact support. |
For issues not covered here, please contact EARU customer support.
8. Zehaztapenak
Irudiaren deskribapena: This image displays the physical dimensions of the ATS (90mm width, 96mm height, 66mm depth) and a table of detailed technical specifications, including current rating, voltage, frequency, and various protection setting ranges.
| Ezaugarri | Xehetasuna |
|---|---|
| Marka | EARU |
| Modelo zenbakia | EARU-1012 |
| Eragiketa modua | PIZTU ITZALI |
| Egungo balorazioa | 63 Amps |
| Bolumen eragileatage | 440 Volts (AC 3*220V (N-L1/L2/L3)) |
| Maiztasun baloratua | 50/60Hz |
| Kontaktu mota | Normalean irekita |
| Konektore mota | Standard DIN rail 63A |
| Zirkuitu Mota | norabide bakarrekoa |
| Harremanetarako materiala | Kobrea |
| Over Current Protection Setting Range | 1-63A/100A (Default 30A) |
| Continuous Over Current Protection Times | 0-20 Times (Default OFF) |
| Voltage Protection Setting Range | 230-300V (Lehenetsia 270V) |
| Voltage Protection Recover Setting Range | 225-295V (Lehenetsia 265V) |
| Vol. Peantage Protection Setting Range | 140-210V (Lehenetsia 170V) |
| Vol. Peantage Protection Recover Setting Range | 145-215V (Lehenetsia 175V) |
| liburukiatage & Current Protection Recover Delay | 1-500s (Default 30s) |
| Elementuaren pisua | 450 g |
| Paketearen neurriak | 15 x 15 x 15 cm |
| Jatorrizko Herrialdea | India |
9. Bermea eta Laguntza
9.1. Bermearen informazioa
The EARU Electric 3-Phase Auto Transfer Switch (ATS) comes with a 1 urteko fabrikatzailearen bermea erosketa-datatik aurrera. Berme honek materialen eta fabrikazioaren akatsak estaltzen ditu erabilera normalaren pean. Ez ditu instalazio desegokiak, erabilera okerrak, istripuek edo baimenik gabeko aldaketek eragindako kalteak estaltzen.
9.2. Bezeroarentzako arreta
For technical assistance, warranty claims, or any questions regarding your EARU Electric ATS, please contact your retailer or the manufacturer directly. Ensure you have your product model number (EARU-1012) and proof of purchase available when contacting support.
