Cdtech TP300 Bluetooth Module Owner’s Manual

Cdtech TP300 Bluetooth Module

Amaituview
CDI-WC46600A-01 is a Wi-Fi + BLE module independently developed by Cdtech based on the ECR6600-ATS2L chip. ECR6600-ATS2L is a SoC chip designed for smart home IoT terminal devices, supporting Wi-Fi 802.11b/g/n/ax and BLE 5.1 protocols. It includes a power management module, power amplifier, zarata gutxikoa amplifier, and transceiver switch. ECR6600-ATS2L adopts a RISC processor architecture, has ample storage space, rich peripheral interfaces, a more secure encryption mechanism, an on-chip FullMAC architecture, and a wider operating temperature range.

Ezaugarriak

Wi-Fi Ezaugarriak

• Supports IEEE 802.11 b/g/n/ax
• Supports Full MAC, including LMAC and UMAC
• Supports SoftAP, STA, and Wi-Fi direct connection mode
• Supports WMM QoS
• Supports 0.8/1.6/3.2 US security protection intervals
• Supports 802.11 ax MCS0 – MCS7
• The maximum bit rate reaches 150 Mbps
• Both uplink and downlink support MU-OFDMA (STA is supported)
• STA supports beamforming (STA acts as the Beamformer)
• Mid-amble onartzen du
• Supports 20 M and 40 M bandwidth. 802.11ax only supports 20 M bandwidth.
• Supports dual carrier modulation (Dual Carrier Modulation, DCM)

BLE Ezaugarria

• Supports BLE 5.1 protocol (does not support AOA/AOD)
• Supports single-device BLE connection
• Supports synchronous broadcasting and scanning
• Supports enhanced power control
• Output power up to +8 dBm
• Supports adaptive frequency hopping (AFH)
• Datu asinkronoak bidaltzea eta jasotzea onartzen du
• Supports connection parameter update
• Supports extensible data packet length
• Esteka-geruzaren enkriptatzea onartzen du
• LE ping onartzen du

The Wi-Fi subsystem and BLE subsystem share the radio part, including ADC/DAC/PLL. Wi-Fi and BLE can only have one working at a time.

Zehaztapen Orokorra

Pin description and PCBA size

Note: Method for downloading the module: VCC, GND, EN (pull-up), UART0_TX, UART0_RX, RESET_B (connected to the RTS of the serial port)

Module physical picture

Materialen faktura

Ezaugarri elektrikoak

Direct-current characteristic

Suggested working conditions

Reflow soldering curve graph

IPC/JEDEC estandarrari erreferentzia eginez.

• Tenperatura maximoa: <250°C
• Aldiz kopurua: ≤2 aldiz

package figure

Enbalatzeko jarraibideak

1. 700 pieza

   • Each reel is loaded with 700 pcs (leave 20 empty pockets at both the front and back without components).

2. Perform vacuum packaging once the taping process is complete.

3. After vacuum packaging, place the taped reel into the inner box (700 pcs total per box).

4. 700pcs × 5 = 3500pcs

   • Each outer carton holds 5 inner boxes, for a total capacity of: $700\text{ pcs} \times 5 = 3500\text{ pcs}$.

WC46600A-01 is an ESD (Electrostatic Discharge) sensitive component. ESD or peak voltage may cause damage to the device. Although the WC46600A-01 has an internal ESD protection circuit, please handle it with care to avoid causing permanent damage or performance degradation.

Ziurtagiria
Ostalari produktuen fabrikatzaileentzako integrazio-argibideak KDB 996369 D03 OEM Eskuliburua v01r01 arabera

FCC arau aplikagarrien zerrenda
CFR 47 FCC Part 15 Subpart C and Subpart C has been investigated. It is applicable to the modular transmitter.

Erabilera Operatiboko Baldintza Espezifikoak
Antenna Placement Within the Host Platform The module is tested for mobile RF exposure use condition.. The transmitter module may not be co-located with any other transmitter or antenna. In the event that these conditions cannot be met (for exampordenagailu eramangarrien konfigurazio jakin batzuk edo beste transmisore batekin kokatzea), orduan FCC baimena ez da baliozkotzat hartzen eta FCC IDa ezin da azken produktuan erabili. Egoera horietan, OEM integratzailea arduratuko da amaierako produktua (igorlea barne) berriro ebaluatzeaz eta FCC baimen berezi bat lortzeaz.

Modulu mugatuko prozedurak
Ez dago aplikagarri

Trazako antenen diseinuak
Ez dago aplikagarri

RF Esposizioari buruzko gogoetak
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be mobile RF exposure use condition.

Antena mota eta irabazia

• Honako antena hauek modulu honekin erabiltzeko ziurtatuta daude.
• Modulu honekin irabazi berdina edo txikiagoa duten mota bereko antenak bakarrik erabil daitezke.
• Baliteke beste antena mota batzuek eta/edo irabazi handiagoko antenak baimen gehigarria behar izatea funtzionatzeko.

Amaierako produktuen etiketatzearen betetze-informazioa
When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text:“Contains FCC ID:2AATP-TP300”. The FCC ID can be used only when all FCC compliance requirements are met.

Proba moduei eta proba osagarriei buruzko informazioa
This transmitter is tested in mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) class II permissive change re-evaluation or new FCC authorization. Host manufacturer installed this modular with single modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C, 15.209, 15.207 requirements, only if the test result comply with FCC part 15C, 15.209, 15.207 requirement, then the host can be sold legally.

Proba osagarriak, 15. zatia B azpiataleko oharra
This transmitter modular us tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B rules requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of the rules requirements if applicable. As long as all conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this modular installed.

Eskuzko informazioa azken erabiltzaileari
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation of the rules, including the transmitter operation, and should refer to guidance in KDB Publication 996369. OEM/Host Manufacturer Responsibilities: OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules

Nola egin aldaketak - Ohar garrantzitsua
Baldintza hauek bete ezin badira (adibidezampAdibidez, ordenagailu eramangarrien konfigurazio batzuk edo beste transmisore batekin batera kokapena), FCC baimena ez da baliozkotzat jotzen eta FCC IDa ezin da azken produktuan erabili. Egoera hauetan, OEM integratzailea izango da azken produktua (transmisorea barne) berriro ebaluatzeaz eta FCC baimen bereizi bat lortzeaz arduratuko dena.

FCC Adierazpena

Gailu hau OEM integratzaileentzat bakarrik dago pentsatuta, baldintza hauetan

1. Antena erabiltzailearen eta antenaren artean 20 cm-ko distantzia mantenduz instalatu behar da.
2. Baliteke transmisore-modulua ez egotea beste transmisore edo antena batekin batera.

• Module Antenna Type: 2.4GHz onboard FPC Antenna, 2.68 dBi peak gain.

Gailu honek FCC Arauen 15. zatia betetzen du. Funtzionamendua honako bi baldintza hauen menpe dago:

1. Baliteke gailu honek ez du interferentzia kaltegarririk eragin.
2. Gailu honek jasotako edozein interferentzia onartu behar du, nahi ez den funtzionamendua eragin dezakeen interferentziak barne.

Oharra: bekadunak ez du erantzukizunik izango betetzearen arduradunak espresuki onartu ez dituen aldaketa edo aldaketengatik. Aldaketa horiek ekipamendua erabiltzeko erabiltzailearen baimena baliogabetu dezakete.

OHARRA: Ekipo hau probatu egin da eta B Klaseko gailu digital baten mugak betetzen dituela ikusi da, FCC Arauetako 15. zatiaren arabera. Muga hauek etxebizitza-instalazio batean interferentzia kaltegarrien aurka arrazoizko babesa emateko diseinatuta daude. Ekipo honek erabilerak sortzen ditu eta irrati-maiztasunaren energia igor dezake eta, argibideen arabera instalatu eta erabiltzen ez bada, interferentzia kaltegarriak sor ditzake irrati-komunikazioetan. Dena den, ez dago bermatzen instalazio jakin batean interferentziarik gertatuko ez denik. Ekipo honek irrati- edo telebista-harreran interferentzia kaltegarriak eragiten baditu, eta hori ekipoa itzali eta piztuz jakin daiteke, erabiltzaileari gomendatzen zaio interferentziak zuzentzen saiatzea, neurri hauetako bat edo gehiago erabiliz:

• Berbideratu edo lekuz aldatu antena hartzailea.
• Handitu ekipoaren eta hargailuaren arteko bereizketa.
• Konektatu ekipoa hargailua konektatuta dagoen zirkuitu desberdineko entxufe batera.
• Kontsultatu banatzaileari edo irrati/telebistako teknikari esperientziadun bati laguntza lortzeko.

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The host integrator must follow the integration instructions provided in this document and ensure that the composite system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369. The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation and should refer to guidance in KDB Publication 996369.OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule, such as FCC Part 15 Subpart B, before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and RF Exposure essential requirements of the FCC rules.

RF Esposizioaren Adierazpena
Ekipo honek kontrolatu gabeko ingurune baterako ezarritako FCC erradiazioaren esposizio-mugak betetzen ditu. Ekipo hau erradiadorearen eta gorputzaren artean gutxienez 20 cm-ko distantzian instalatu eta funtzionatu behar da