Instalatu Cisco Catalyst sareko interfazearen modulua
Atal honek Cisco Catalyst Network Interface Modules (NIM) instalazioa egin aurretik eta bitartean egiten den informazioa eskaintzen du Cisco Catalyst 8200 Series Edge Platformetan.
Amaituview Sareko interfazearen modulua
The Cisco Catalyst Network Interface Module (NIM) is supported on Cisco Catalyst 8200 Series Edge Platforms.
These are the steps to install a NIM:
1. Aurkitu NIM zirrikitua aurrealdeko panelean.
2. Loosen the screws to remove NIM blank cover.
3. Sartu NIM txartela zirrikituan.
4. Estutu torlojuak NIM zirrikituan finkatzeko.
These are the steps to remove a NIM:
1. If the NIM is up and running, issue the following command to shut down the NIM gracefully before removing it:
hw-module subslot slot 0/2 stop
Kontuz If you do not shut down the NIM gracefully before removing it, the NIM card could get damaged.
2. Aurkitu NIM zirrikitua aurrealdeko panelean.
3. Askatu NIM finkatzen duten torlojuak.
4. Atera NIM txartela zirrikitutik astiro-astiro.
All module slots must have a module or blank installed for the product to work thermally and for safety purposes.
Informazio gehiago lortzeko, ikus Cisco Catalyst 8200 Series Edge Platforms datu-orria cisco.com webgunean, plataformetan onartzen diren NIMen zerrenda ikusteko.
Sareko interfazearen moduluak kendu eta instalatu
Keep the following tools and equipment while working with the Network Interface Modules (NIM)s:
- 1. Phillips bihurkin edo biribil lau txiki bat
- ESD prebentziozko eskumuturreko uhala
Kendu sareko interfazearen modulua
1. urratsa Shut down the electrical power to the slot in the device, turn off the electrical power to the device. Leave the power cable plugged-in to channel ESD voltages lurrera.
2. urratsa Remove all network cables from the rear panel of the device. Using a number 1 Phillips screwdriver, loosen the captive screws on the network interface module.
3. urratsa Slide the network interface module out.
4. urratsa If you are not replacing the module, install a blank faceplate over the empty slot to ensure proper air flow.
Instalatu Cisco Catalyst sareko interfazearen moduluak
1. urratsa Shut down the electrical power to the slot in the router by turning off the electrical power to the router. Leave the power cable plugged in to channel ESD voltages lurrera.
2. urratsa Remove all network cables from the rear panel of the device.
3. urratsa Remove the blank faceplates installed over the network interface module slot that you intend to use.
Oharra Save blank faceplates for future use.
4. urratsa Align the module with the guides in the chassis walls or slot divider and slide it gently into the NIM slot on the device.
5. urratsa Push the module into place until you feel the edge connector seat securely into the connector on the router backplane. The module faceplate should contact the chassis rear panel.
6. urratsa Using a number 1 Phillips screwdriver, tighten the captive screws on the network interface module.
7. urratsa Connect the module to the network and re-enable the power to the slot in the device.
Instalatu Cisco Catalyst sareko interfazearen modulua
Dokumentuak / Baliabideak
 |
CISCO 8200 Serieko Katalizatzaile Sareko Interfaze Modulua [pdfErabiltzailearen gida 8200 Seriea, 8200 Seriea Catalyst Sareko Interfaze Modulua, Catalyst Sareko Interfaze Modulua, Sare Interfaze Modulua, Interfaze Modulua |