CISCO-LOGOA

CISCO ESW6300 USB ataka gaitzea sarbide puntuetan

CISCO-ESW6300-Enabling-USB-Port-on-Access-Points-PRODUCT

Zehaztapenak

  • USB Port Power: Up to 2.5W (some models support up to 4.5W)
  • USB ataka funtzioa: USB gailuentzako energia iturria

Produktuak erabiltzeko jarraibideak

USB ataka gaitzea sarbide puntuetan:
To enable the USB port on your Cisco Access Point for powering USB devices:

  1. Check if your AP model supports a USB power source by referring to the datasheet.
  2. Konfiguratu AP Pro batfile CLI erabiliz:
    • Sartu konfigurazio modu orokorrean: configure terminal
    • Sortu AP profesional batfile: ap profile xyz-ap-profile
    • Gaitu USBa AP pro-rakofile: usb-enable
    • Irten konfigurazio modutik: end
  3. Konfiguratu USB ezarpenak sarbide-punturako CLI erabiliz:
    • Sartu pribilegiodun EXEC modura: enable
    • Enable the USB port on the AP: ap name AP44d3.xy45.69a1 usb-module override

USB ataka sarbide-puntuetarako energia-iturri gisa
Some Cisco APs have a USB port that can act as a source of power for some USB devices. The power can be up to 2.5W; if a USB device draws more than 2.5W of power, the USB port shuts down automatically. The port is enabled when the power draw is 2.5W or lower. Refer to the datasheet of your AP to check if the AP has a USB port that can act as a source of power.

Oharra 
Both IW6300 and ESW6300 APs have a USB port that can act as a source of power up to 4.5W for some USB devices.

Oharra
The controller records the last five power-overdrawn incidents in its logs.

Kontuz

When an unsupported USB device is connected to the Cisco AP, the following message is displayed:
The inserted USB module is not a supported device. The behaviour of this USB device and its impact on the Access Point are not guaranteed. If Cisco determines that a fault or defect can be isolated due to the use of third-party USB modules installed by a customer or reseller, Cisco may withhold support under warranty or the support program under contract. In the course of providing support for Cisco networking products, the end user may be required to install Cisco-supported USB modules in the event Cisco determines that removing third-party parts will assist Cisco in diagnosing the root cause for troubleshooting purposes. Cisco also reserves the right to charge the customer per the then-current time and material rates for services provided to the customer when Cisco determines, after having provided such services, that an unsupported device caused the root cause of the defective product.

AP Pro bat konfiguratzeafile (CLI)

Prozedura

  Agindua edo Ekintza Helburua
1. urratsa konfiguratu terminala

Example:

Gailua # konfiguratu terminala

Konfigurazio modu orokorrean sartzen da.
2. urratsa ap profileAP-profilee

Example:

Gailua (konfigurazioa) # ap profile xyz-ap-profile

AP pro bat konfiguratzen dufile and enters the AP profile konfigurazio modua.

Oharra

When you delete a named profile, the APs associated with that profile will not revert to the default profile.

3. urratsa usb-enable

Example:

Gailua (config-ap-profile)# usb-enable

USB gaitzen du AP pro bakoitzerakofile.

Oharra

By default, the USB port on the AP is disabled.

 

Erabili no USB-Enable command to disable USB for each AP profile.

4. urratsa amaiera

Example:

Gailua (config-ap-profile)# amaiera

EXEC modu pribilegiatura itzultzen da. Bestela, sakatu ere egin dezakezu Ktrl-Z konfigurazio modu orokorretik irteteko.

USB ezarpenak konfiguratzea sarbide-puntu baterako (CLI)

Prozedura

  Agindua edo Ekintza Helburua
1. urratsa gaitu

Example:

Gailua # gaitu

EXEC modu pribilegiatuan sartzen da.
2. urratsa ap izena ap-izena usb-module

Example:

Gailua # ap name AP44d3.xy45.69a1 usb-module

Enables the USB port on the AP.

Erabili ap izena ap-izena no usb-module

Command to disable the USB port on the AP.

Oharra

If you are using a Cisco Catalyst 9105AXW AP and you enable the USB port (3at PoE-in), it is not possible to enable the USB PoE-out at the same time.

3. urratsa ap izena ap-izena usb-module override

Example:

Gailua # ap name AP44d3.xy45.69a1 usb-module override

Overrides the USB status of the AP profile and considers the local AP configuration.

Erabili ap izena ap-izena no usb-module override command to override the USB status of the AP and consider the AP profile

konfigurazioa.

Oharra

You can configure the USB status for an AP only if you enable USB override for it.

USB ezarpenak konfiguratzea sarbide-puntu (GUI) baterako

Prozedura

  • Step 1: Choose Configuration >Wireless > Access Points.
  • Step 2: In the Access Points window, click the name of the AP.
  • Step :3 In the Edit AP window, click the Interfaces tab.
  • Step: 4 In the USB Settings section, configure the USB Module State as either of the following:
    • ENABLED: Enables the USB port on the AP
    • DISABLED: Disables the USB port on the AP
  • Oharra
    If you are using Cisco Catalyst 9105AXW AP and if you enable the USB por3at3at PoE-in, it is not possible to enable the USB PoE-out at the same time.
  • Step 5: Configure USB Override as either of the following:
    • ENABLED: Overrides USB status of the AP profile and considers the local AP configuration
    • DISABLED: Overrides USB status of the AP and considers the AP profile konfigurazioa
    • Oharra
      You can configure the USB status for an AP only if you enable USB override for it.
  • Step 6: Click Apply & Update to Device.

Sarbide-puntuetarako USB konfigurazioak monitorizatzea (CLI)

  • To view the inventory details of APs, use the following command: show ap name ap-name inventory
  • Honako hau daampfitxategiaren irteera:
    • Device# show ap name AP500F.8059.1620 inventory
    • Device# show ap name AP500F.8059.1620 inventory
  • Honako hau daampfitxategiaren irteera:
    • NAME: AP280  DESCR: Cisco Aironet 2800 Series (IEEE 802.11ac) Access Point
    • PID: AIR-AP2802I-D-K9 , VID: 01, SN: XXX1111Y2ZZZZ2800
    • NAME: SanDisk, DESCR: Cruzer Blade
    • PID: SanDisk , SN: XXXX1110010, MaxPower: 224
  • To view the summary of an AP module, use the following command: show ap module summary
  • Honako hau daampfitxategiaren irteera:
    • Gailua # erakutsi AP moduluaren laburpena
  • AP Name External Module External Module PID External Module

Deskribapena
AP500F.1111.2222 Enable SanDisk Cruzer Blade

  • To view the USB configuration details for each AP, use the following command: show ap name ap-name config general
  • Honako hau daampfitxategiaren irteera:
    • Gailua # erakutsi AP izena AP500F.111.2222 konfigurazio orokorra
    • USB Module Type……………………………. USB Module
    • USB Module Status………………………….. Disabled
    • USB Module Operational State………………… Enabled
    • USB Override …………………………….. Enabled
  • To view sthe status of the USB module, use the following command: show ap profile xyz izena zehaztuta
  • Honako hau daampfitxategiaren irteera:
    • Gailua # erakutsi ap profile xyz izena zehaztuta
    • USB Module: ENABLED

Ohiko galderak

Q: How can I tell if my AP supports a USB power source?

A: You can refer to the datasheet of your AP to check if it has a USB port that can act as a power source for USB devices.

G: Zer gertatzen da konektatutako USB gailu batek 2.5 W baino gehiagoko potentzia kontsumitzen badu?

A: If a USB device draws more than 2.5W of power, the USB port shuts down automatically to prevent damage.

Dokumentuak / Baliabideak

CISCO ESW6300 USB ataka gaitzea sarbide puntuetan [pdf] Argibideen eskuliburua
IW6300, ESW6300, ESW6300 USB ataka gaitzea sarbide puntuetan, USB ataka gaitzea sarbide puntuetan, USB ataka sarbide puntuetan, Sarbide puntuak

Erreferentziak

Utzi iruzkin bat

Zure helbide elektronikoa ez da argitaratuko. Beharrezko eremuak markatuta daude *