EVENT LIGHTING APRO4-IP DMX Controller

Zure segurtasunerako, irakurri arretaz erabiltzailearen eskuliburu hau erabili aurretik.
Event Lighting-ek eskuliburua edozein unetan berrikusteko eskubidea du. Eskuliburu honetako informazioa eta zehaztapenak jakinarazi gabe alda daitezke. Event Lighting-ek ez du bere gain hartzen akatsen edo hutsegiteen erantzukizunik edo erantzukizunik. Mesedez, kontsultatu Ekitaldien Argiztapena elementu honi buruzko edozein argibide edo informazio lortzeko.

EZAUGARRIAK

• DMX 512, RDM, Artnet and sACN support
• Urruneko konfigurazioa barne bidez weborrialdea
• Update firmware on Weborrialdea
• DMX output isolation
• RJ45 Ethernet B input with POE（DC12V 2A）
• LCD pantaila
• Gigabit network, 100/1000mbps port speed
• IP65 balorazioa

PANELA BUKATUTAVIEW

1. Ethernet port RJ45
2. Ethernet port RJ45
3. Power in/out True1
4. 2xDMX5pin connectors
5. 2xDMX5pin connectors
6. Fusiblearen euskarria
7. LCD Display protection cover

MENUAK
Below is controller Menus map

NagusiaMenua	Azpimenua 1	Azpimenua 2	Balioa/Aukera	Lehenetsia
Sarea	IP modua		DHCP	Estatikoa
			Estatikoa
	IP helbidea		2.xx.xx.xx	2.xx.xx.xx
	Azpisareko maskara		255.0.0.0	255.0.0.0
DMX ataka	Protokoloa	Artnet		Artnet
		sACN
	Start Net		000-127	000
	Hasi Unibertsoa		000-255	000
	Portua 1	Modua	Desaktibatuta	On
			On
		SAREA	000-127	000
		Unibertsoa	000-255	000
	Portua 2	Modua	Desaktibatuta	On
			On
		SAREA	000-127	000
		Unibertsoa	000-255	001
	Portua 3	Modua	Desaktibatuta	On
			On
		SAREA	000-127	000
		Unibertsoa	000-255	002
	Portua 4	Modua	Desaktibatuta	On
			On
		SAREA	000-128	000
		Unibertsoa	000-255	003
			Desgaitu
Ezarpenak	DMX tasa		20Hz	30Hz
			25Hz
			30Hz
			35Hz
			40Hz
	RDM	Desgaitu		Desgaitu
		Gaitu
	Bistaratu aktibatuta	Beti		1min
		30 seg
		1min
		5min
	Seinalearen galera	Eutsi DMX		Eutsi DMX
		Stop Output
	Bateratze modua	PH		PH
		LTP
	Fabrika berrezarri	Ez		Ez
		Bai

WEB konfigurazioa

NET device network IP mode can set to DHCP mode or Static mode.

DHCP modua

• When APRO4‐IP is set to DHCP mode, you need to set the computer to DHCP also. And use a router for linking computer and APRO4‐IP device. The controller will show IP address like below:
• Enter IP address in your web browser, then you can login webpage to configure the parameter of controller.

Sartu pasahitza: admin

Modu estatikoa

• When APRO4‐IP device is set to Static mode, you need to set computer to be Static mode also. APRO4‐IP device will show IP address as below:
• Then set the IP address of computer is in the same IP range manually. For example: IP address must start with 2 according to APRO4‐IP address. And netmask is same with 255.0.0.0.
• Input static IP address of APRO4‐IP device in your browser, then you can login to configure the parameter of device.

Sartu pasahitza: admin

• When log on NET Config web, the first page show the information about APRO4‐IP.
• Following  is  for  Network  setting,  you  can  set  IP  mode  to  be  Static  or  DHCP,  IP  Address,and Subnet Mask. After setting, click Save button .
• For DMX Port page , it is used for DMX Port setting. You can select Protocol to be Artnet or sACN, and set each port as input or output.
• On the page of Setting , you can set DMX Rate, RDM , Display On and Signal Loss. After setting, click Save to store the setting.
• DMX  Rate:  You  can  set  20Hz,  25Hz,  30Hz,  35Hz,  40Hz,  30Hz  is default setting.
• RDM: You can set RDM to be Disable or Enable.
• There is 4 options for Display On mode: Always, 30Sec, 1Min, 5Min.
• Seinalearen galera: Can set as Hold DMX or Stop Output.
• You can return to factory setting by click Factory Reset button.
• On Update page, you can update software of fixture by selecting the update software file of APRO4‐IP.
• On the last page, you can reset password.

ZEHATZA

• Sarrerako potentzia: AC 100‐240V,50/60Hz
• Energia kontsumoa: AC240V 50HZ 0.05A
• Tamaina: 215.3×150.5x42mm 4.2W
• Pisua: 1.43Kg
• POE 802.3af
• IP65

NEURRIAK

Bermea

Mesedez, jo zure tokiko banatzailera edo jarri harremanetan Event Lighting-ekin. www.event‐lighting.com.au

Maiz egiten diren galderak

How do I reset the APRO4-IP device to factory settings?

To perform a factory reset on the APRO4-IP device, access the Factory Reset option in the Main Menu under Settings. Confirm the reset to restore the device to its default configuration.

What is the default IP address for the APRO4-IP device?

The default IP address for the APRO4-IP device is set to DHCP mode. If you switch to Static mode, you can set a specific IP address within the range provided in the user manual.

Dokumentuak / Baliabideak

EVENT LIGHTING APRO4-IP DMX Controller [pdfErabiltzailearen eskuliburua APRO4-IP, APRO4-IP DMX Controller, DMX Controller, Controller

Erreferentziak

• Erabiltzailearen eskuliburua