M5StickC Plus2 Eragiketa Gida
Fabrikako firmware
Gailuak funtzionamendu-arazoak dituenean, fabrikako firmwarea berriro flasheatzen saia zaitezke hardwarearen akatsen bat dagoen egiaztatzeko. Ikusi hurrengo tutoriala. Erabili M5Burner firmwarea flashatzeko tresna fabrikako firmwarea gailuan flasheatzeko.
Ohiko galderak
1. galdera: Zergatik dago nire M5StickC Plus2 pantaila beltza/ez da abiarazten?
Irtenbideak: M5Burner Burn official Factory Firmware“M5StickCPlus2 User Demo”
2.G: Zergatik 3 ordu baino ez ditu funtzionatzen? Zergatik kargatzen da %100ean minutu 1ean, kargatzeko kablea kendu eta itzali egingo da?
Solutions: “Bruce for Stack plus2”This is an unofficial firmware. Flashing unofficial firmware can void your warranty, cause instability, and expose your device to security risks. Proceed with caution.
Please burn back official firmware.
Prestaketa
- Ikusi M5Burner tutoriala firmwarearen flashatze tresnaren deskarga osatzeko, eta ondoren ikusi beheko irudia dagokion firmwarea deskargatzeko.
Deskargatzeko esteka: https://docs.m5stack.com/en/uiflow/m5burner/intro
USB Driver Instalazioa
Gidariaren instalazio aholkua
Egin klik beheko estekan zure sistema eragileari dagokion kontrolatzailea deskargatzeko. CP34X-rako kontrolatzaile paketea (CH9102 bertsiorako) deskargatu eta instalatu daiteke zure sistema eragileari dagokion instalazio paketea hautatuta. Programa deskargatzean arazoak badituzu (adibidez, denbora-muga edo "Huts egin da helburu RAMean idaztean" erroreak), saiatu gailuaren kontrolatzailea berriro instalatzen.
CH9102_VCP_SER_Windows
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_SER_Windows.exe
CH9102_VCP_SER_MacOS 1.7 bertsioa
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_MacOS_v1.7.zip
Portuen hautaketa MacOS-en
MacOS-en, bi ataka erabilgarri egon daitezke. Erabiltzerakoan, hautatu wchmodem izeneko ataka.
Portu aukeraketa
Konektatu gailua ordenagailura USB kable baten bidez. Gidariaren instalazioa amaitutakoan, dagokion gailuaren ataka hauta dezakezu M5Burner-en.
Erre
Egin klik “Grabatu” aukeran flasheatzeko prozesua hasteko.
MakilaC-Plus2
SKU: K016-P2
Deskribapena
StickC-Plus2 is the iterative version of Stick C-Plus. It is powered by the ESP32-PICO-V3-02 chip, providing Wi-Fi connectivity. Within its compact body, it integrates a rich variety of hardware resources, including IR emitter, RTC, microphone, LED, IMU, buttons, buzzer, and more. It features a 1.14-inch TFT display driven by the ST7789V2 with a resolution of 135 x 240.
The battery capacity has been increased to 200 mAh, and the interface is compatible with both HAT and Unit series modules.
This sleek and compact development tool can ignite unlimited creativity. StickC-Plus2 helps you quickly build IoT product prototypes and greatly simplifies the entire development process. Even beginners who are new to programming can create interesting applications and apply them in real life.
Tutoretza
UIFlow
Tutorial honek StickC-Plus2 gailua UIFlow programazio plataforma grafikoaren bidez nola kontrolatu erakutsiko du.
UiFlow2
Tutorial honek StickC-Plus2 gailua UiFlow2 programazio plataforma grafikoaren bidez nola kontrolatu erakutsiko du.
Arduino IDEa
Tutorial honek StickC-Plus2 gailua Arduino IDE erabiliz nola programatu eta kontrolatu erakutsiko du.
Oharra
Port Not Recognized
When using a C-to-C cable, if the port cannot be recognized, please perform the following power-on procedure:
disconnect StickC-Plus2, power it off (long-press the power button until the green LED lights up), then reconnect the USB cable to power on.
Ezaugarriak
- Based on ESP32-PICO-V3-02 with Wi-Fi support
- Built-in 3-axis accelerometer and 3-axis gyroscope
- Integrated IR emitter
- Built-in RTC
- Mikrofono integratua
- User buttons, 1.14-inch LCD, power/reset button
- 200 mAh Li-ioizko bateria
- Hedapen-konektorea
- Integrated passive buzzer
- Wearable & mountable
- Garapen Plataforma
- UiFlow1
- UiFlow2
- Arduino IDEa
- ESP-IDF
- PlataformaIO
barne hartzen ditu
- 1 x StickC-Plus2
Aplikazioak
- Eraman daitezkeen gailuak
- IoT controller
- STEM education
- Brikolaje proiektuak
- Etxe adimenduneko gailuak
Zehaztapenak
| Zehaztapena | Parametroa |
| SoC | ESP32-PICO-V3-02 240 MHz-ko nukleo bikoitza, Wi-Fi, 2 MB PSRAM, 8 MB Flash |
| Sarrera boltage | 5 V @ 500 mA |
| Interfazea | C mota x 1, GROVE (I2C + S/I + UART) x 1 |
| LCD pantaila | 1.14 hazbeteko, 135 x 240 koloretako TFT LCD, ST7789V2 |
| Mikrofonoa | SPM1423 |
| Botoiak | Erabiltzaile botoiak x 3 |
| LED | Green LED x 1 (non-programmable, sleep indicator) Red LED x 1 (shares control pin G19 with IR emitter) |
| RTC | BM8563 |
| Burrunbagailua | Txirrina pasibo integratua |
| IMU | MPU6886 |
| Antena | 2.4 G 3D antena |
| Kanpoko pinak | G0, G25/G26, G36, G32, G33 |
| Bateria | 200 mAh @ 3.7 V, barruan |
| Eragiketa Tenperatura | 0 ~ 40 °C |
| Itxitura | Plastikoa (PC) |
| Produktuaren Tamaina | 48.0 x 24.0 x 13.5 mm |
| Produktuaren pisua | 16.7 g |
| Paketearen tamaina | 104.4 x 65.0 x 18.0 mm |
| Pisu Gordina | 26.3 g |
Eragiketa-jarraibideak
Piztu/Itzali
Power-on: Press the “BUTTON C” for more than 2 seconds, or wake up via the RTC IRQ signal. After the wake-up signal is triggered, the program must set the HOLD pin (G4) to high (1) to keep the power on, otherwise the device will shut down again.
Power-off: Without external USB power, press “BUTTON C” for more than 6 seconds, or set HOLD (GPIO4)=0 in the program to power off. While USB is connected, pressing “BUTTON C” for more than 6 seconds will turn off the screen and enter sleep mode (not a full power-off).
Eskemak
Pin mapa
LED gorria eta IR igorlea | A botoia | B botoia | Buzzerra
| ESP32-PICO-V3-02 | GPIO19 | GPIO37 | GPIO39 | GPIO35 | GPIO2 |
| IR Emitter & Red LED | IR emitter & Red LED pin | ||||
| A botoia | A botoia | ||||
| B botoia | B botoia | ||||
| C botoia | C botoia | ||||
| Buzzer pasiboa | Burrunbagailua |
Koloretako TFT pantaila
Driver IC: ST7789V2
Bereizmena: 135 x 240
| ESP32-PICO-V3-02 | G15 | G13 | G14 | G12 | G5 | G27 |
| TFT pantaila | TFT_MOSI | TFT_CLK | TFT_DC | TFT_RST | TFT_CS | TFT_BL |
Mikrofonoa (SPM1423)
| ESP32-PICO-V3-02 | G0 | G34 |
| MIC SPM1423 | CLK | DATUAK |
6 ardatzeko IMU (MPU6886) eta RTC BM8563
| ESP32-PICO-V3-02 | G22 | G21 | G19 |
| IMU MPU6886 | SCL | SDA | |
| BM8563 | SCL | SDA | |
| IR emisorea | TX | ||
| LED gorria | TX |
HY2.0-4P
| HY2.0-4P | Beltza | Gorria | Horia | Zuria |
| PORT.CUSTOM | GND | 5V | G32 | G33 |
Ereduaren Tamaina
Fitxa teknikoak
ESP32-PICO-V3-02
ST7789V2
BM8563
MPU6886
SPM1423
Softwareak
Arduino
StickC-Plus2 Arduino Quick Start
StickC-Plus2 Library
StickC-Plus2 Factory Test Firmware
UiFlow1
StickC-Plus2 UiFlow1 Hasiberrientzako
UiFlow2
StickC-Plus2 UiFlow2 Hasiberrientzako
PlataformaIO
[env:m5stack-stickc-plus2]
platform = espressif32@6.7.0
board = m5stick-c
framework = arduino
upload_speed = 1500000
monitor_speed = 115200
build_flags =
-DBOARD_HAS_PSRAM
-mfix-esp32-psram-cache-issue
-DCORE_DEBUG_LEVEL=5
lib_deps =
M5Unified=https://github.com/m5stack/M5Unified
USB kontrolatzailea
Click the links below to download the driver that matches your operating system. The package contains CP34X drivers (for CH9102). After extracting the archive, run the installer that matches your OS bit-depth.
If you encounter issues such as timeout or “Failed to write to target RAM” during downloading, please try reinstalling the driver.
| Gidariaren izena | Supported Chip | Deskargatu |
| CH9102_VCP_SER_Windows | CH9102 | Deskargatu |
| CH9102_VCP_SER_MacOS 1.7 bertsioa | CH9102 | Deskargatu |
macOS Port Selection
Two serial ports may appear on macOS. Please select the port named wchmodem.
Easy loader
Easy Loader is a lightweight program flasher that comes with a demonstration firmware. By following a few simple steps, you can flash it to the controller for quick functional verification.
| Easy loader | Deskargatu | Oharra |
| Factory Test for Windows | deskargatu | / |
Bestela
StickC-Plus2 fabrikako firmwarea leheneratzeko gida
Bideoa
StickC-Plus2 Feature Introduction
StackC Plus2 视频.mp4
Bertsio-aldaketa
| Argitaratze data | Aldatu deskribapena | Oharra |
| / | Lehenengo kaleratzea | / |
| 2021-12 | Added sleep and wake-up function, version updated to v1.1 | / |
| 2023-12 | Removed PMIC AXP192, MCU changed from ESP32-PICO-D4 to ESP32-PICO-V3-02, different power-on/off method, version v2 | / |
Produktuen Konparaketa
Hardware desberdintasunak
| Produktua Izena |
SoC | Potentzia kudeaketa | Bateria Edukiera | Memoria | USB-UART txipa | Kolorea |
| Stick C-Plus | ESP32-PICO-D4 | AXP192 | 120 mAh | 520 KB SRAM + 4 MB Flash | CH522 | Red- orange |
| MakilaC-Plus2 | ESP32-PICO-V3-02 | / | 200 mAh | 2 MB PSRAM + 8 MB Flash | CH9102 | Laranja |
Pin desberdintasunak
| Produktuaren izena | IR | LED | TFT | A BOTOIA | B BOTOIA | C BOTOIA (ESNATU) |
EUTSI | Bateria liburukiatage Detektatu |
| M5STICKC PLUS | G9 | G10 | MOSI (G15) CLK (G13) DC (G23) RST (G18) CS (G5) |
G37 | G39 | Erregularra botoia |
/ | AXP192 bidez |
| M5STICKC PLUS2 | G19 | G19 | MOSI (G15) CLK (G13) DC (G14) RST (G12) CS (G5) |
G37 | G39 | G35 | G4 | G38 |
Pizteko/itzaltzeko desberdintasunak
| Produktua Izena | Piztu | Itzali |
| Stick C- Plus2 | Press “BUTTON C” for more than 2 s, or wake via RTC IRQ. After wake-up, set HOLD (G4)=1 in the program to keep power on, otherwise the device will shut down again. |
Without USB power, press “BUTTON C” for more than 6 s, or set HOLD (GPIO4)=0 in the program to power off. With USB connected, pressing “BUTTON C” for more than 6 s will turn off the screen and enter sleep, but not a full power- off. |
StickC-Plus2-k PMIC AXP192 kentzen duenez, pizteko/itzaltzeko metodoa aurreko bertsioetatik desberdina da. Dokumentu honen hasieran aipatu bezala, funtzionamendua antzekoa da neurri handi batean, baina onartutako liburutegiak desberdinak izango dira. Wi-Fi eta IR seinaleen indarra hobetu egin da aurreko modeloarekin alderatuta.
Dokumentuak / Baliabideak
 |
M5STACK ESP32-PICO-V3-02 IoT Garapen Modulua [pdfErabiltzailearen gida ESP32-PICO-V3-02 IoT Garapen Modulua, ESP32-PICO-V3-02, IoT Garapen Modulua, Garapen Modulua, Modulua |