M5STACK Unit C6L Intelligent Edge Computing Unit Erabiltzailearen Eskuliburua

M5STACK Unit C6L Intelligent Edge Computing Unit Erabiltzailearen Eskuliburua
DOMUS LINE EASi DISK Driver D Mugimendu Kontrol Diskoaren Erabiltzaile Eskuliburua

1. ESKEMA

Unit C6L is an intelligent edge computing unit integrated with the M5Stack_Lora_C6module — featuring an Espressif ESP32-C6 SoC and Semtech SX1262 LoRa transceiver — and engineered with a modular design for long-range, low-power LoRaWAN communication alongside high-speed 2.4 GHz Wi-Fi and BLE connectivity.
It includes a 0.66″ SPI OLED display for real-time data visualization, a WS2812Caddressable RGB LED for system-status indication, a built-in buzzer for audible alerts, and front-panel buttons (SYS_SW) with a reset switch for local interaction. Astandard Grove I²C interface allows seamless integration with M5Stack hosts and various Grove sensors. The onboard USB Type-C port supports ESP32- C6 firmware programming, serial debugging, and 5 V power input, while automatic power switching and multi-channel ESD/surge protection ensure stable operation. Unit C6L excels at real-time data acquisition, edge-intelligence processing, and remote control, making it ideal for IoT applications such as smart agriculture, environmental monitoring, industrial IoT, smart buildings, asset tracking, and urban infrastructure sensing.\

1.1. C6L unitatea

  1. Komunikazio-gaitasunak
    Integrated LoRa (Semtech SX1262), supporting LoRaWAN Class A/B/Candpointto-point modes 2.4 GHz Wi-Fi and BLE via ESP32-C6-MINI-1U
  2. Prozesadorea eta errendimendua
    Main Controller: Espressif ESP32-C6 (single-core RISC-V, up to 40 MHz) On-chip Memory: 512 KB SRAM with integrated ROM
  3. Energia eta Energia Kudeaketa
    Power Input: USB Type-C (5 V input) and Grove 5 V input
  4. Pantaila eta adierazleak
    0.66″ SPI OLED display for real-time data visualization and status monitoringWS2812C addressable RGB LED for system-status indication Built-in buzzer for audible alerts
  5. Interfaces & Controls
    Grove I²C interface (with 5 V power) for seamless connection to M5Stack hostsandGrove sensors USB Type-C port for firmware programming, serial debugging, and power input Front-panel buttons (SYS_SW) and reset switch (MCU_RST) for local control
  6. Expansion & Debug Pads
    Bootloader pad: predefined jumper pad for entering bootloader mode Test points (TP1–TP8) for signal probing and in-circuit debug

2. ZEHATZAK

Parametroa Zehaztapena
MCU Espressif ESP32-C6 (RISC-V nukleo bakarrekoa, 40 MHz-ra arte)
Komunikazioa LoRaWAN; 2.4 GHz Wi-Fi BLE
Potentzia Sarrera USB C motakoa (5V) eta Grove 5V
Hornidura Boltage 3.3 V (barneko LDO)
Flash biltegiratzea 16 MB SPI Flasha (128 Mbit)
Bistaratzea 0.66”SPI OLED(128×64)
Adierazlea                                  WS2812C helbideragarria den RGB LED
Burrunbagailua Ontziko txirrina
Botoiak System button (SYS_SW)and reset button(MCU_RST)
Interfazeak Grove I²C; USB C motakoa; abioko kargatzaile-panel; TP1-TP8 arazketa-panelak
Antenak 2×SSMB-JEF clamp konektoreak; 2×IPEX-4 antena konektoreak
Funtzionamendu-tenperatura Funtzionamendu-tenperatura
Ezaugarri gehigarriak Multi-channel ESD/surge protection
Fabrikatzailea M5Stack Technology Co., Ltd Block A10, Expo Bay South Coast, Fuhai Street, Bao’an District, Shenzhen, China
Frequency Range for CE 2.4G Wi-Fi: 2412-2472MHz BLE: 2402-2480MHz Lora: 868-868.6MHz
CErako gehienezko EIRP BLE: 5.03dBm 2.4G Wi-Fi: 16.96dBm Lora: 9.45dBm
Hartzailearen kategoria The equipment provider declared that the receiver category for the EUTis2.
2.1 Moduluaren tamaina
Moduluaren Tamaina

3. FCC abisua

FCC kontua:
Betearen arduradunak espresuki onartzen ez dituen aldaketak edo aldaketak ekipamendua erabiltzeko erabiltzailearen eskumena baliogabetu dezake. Gailu honek FCC Arauen 15. zatia betetzen du. Funtzionamendua bi baldintza hauen menpe dago: (1) Gailu honek ez du interferentzia kaltegarririk eragin, eta (2) gailu honek jasotako edozein interferentzia onartu behar du, nahi ez den funtzionamendua eragin dezakeen interferentziak barne.
OHAR GARRANTZITSUA:
Oharra: This equipment has been tested and found to comply with the limits for a ClassBdigital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
zuzendu interferentzia neurri hauetako bat edo gehiagoren bidez:

  • Berbideratu edo lekuz aldatu antena hartzailea.
  • Increase the separation betweentheequipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator&your body.
Arduino instalatu

I. Installing Arduino IDE(https://www.arduino.cc/en/Main/Software)
Egin klik Arduino ofiziala bisitatzeko webgunea eta hautatu zure instalazio paketea
operating system to download. Ⅱ. Installing Arduino Board Management
1. Zuzendaritza Batzordea URL is used to index the development board information for specific platform. In the Arduino IDE menu, select File -> Hobespenak
Arduino instalatu

2. Kopiatu ESP plakaren kudeaketa URL behean, Kontseiluko Kudeatzaile Gehigarrian sartu
URLs: field, and save.
https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
Arduino instalatu
Arduino instalatu

3. Alboko barran, hautatu Board Manager, bilatu ESP eta egin klik Instalatu aukeran.
Arduino instalatu

4. Alboko barran, hautatu Board Manager, bilatu M5Stack eta egin klik Instalatu aukeran.
Depending on the product used, select the corresponding development board under
Tools -> Board -> M5Stack -> {ESP32C6 DEV Module board}.
Arduino instalatu

5. Konektatu gailua ordenagailura datu-kable batekin programa kargatzeko

M5STACK Logo

Dokumentuak / Baliabideak

M5STACK unitatea C6L ertzeko konputazio unitate adimenduna [pdf] Erabiltzailearen eskuliburua
M5UNITC6L, 2AN3WM5UNITC6L, C6L unitatea Ertzeko Konputazio Unitate Adimenduna, C6L unitatea, Ertzeko Konputazio Unitate Adimenduna, Ertzeko Konputazio Unitatea, Konputazio Unitatea, Unitatea

Erreferentziak

Utzi iruzkin bat

Zure helbide elektronikoa ez da argitaratuko. Beharrezko eremuak markatuta daude *