DATALOGGER INSTRUCTIONS

OHAR GARRANTZITSUA

You MUST download one of the Mobile Apps below to retrieve data and configure device

---

Bluetooth BAKARRIK

---

Download TraceableGO™ App

---

---

Bluetooth + Cloud Data Storage

---

TraceableLIVE® Subscription REQUIRED

---

NOW that one of the apps below have been installed on your mobile device

TraceableGO comes ready to use out of the box.

TraceableGO™ App Free Download DOAN Ezaugarriak
	Configure datalogger: Ezarri alarma Change Logging Interval Aldatu °C/°F artean Start/Stop Options Memoria-biltzea
	Export, Email and Save PDF to Mobile Device
	UNLIMITED CLOUD DATA STORAGE
	Data download to CSV, or Secured PDF
	Graphical UI to analyze data
	Summary data display: Min/Max, Kinetic Mean, Time in Alarm
	Storage of trip parameters
	21 CFR 11 Compliance

TraceableLIVE® App Doako Deskarga 30 $/hilean Ezaugarriak
	Configure datalogger: Ezarri alarma Change Logging Interval Aldatu °C/°F artean Start/Stop Options Memoria-biltzea
	Export, Email and Save PDF to Mobile Device
	UNLIMITED CLOUD DATA STORAGE
	Data download to CSV, or Secured PDF
	Graphical UI to analyze data
	Summary data display: Min/Max, Kinetic Mean, Time in Alarm
	Storage of trip parameters
	21 CFR 11 Compliance

KONFIGURTU GAILUA

OHARRA: To configure device either TraceableGO™ or TraceableLIVE® Apps must be downloaded to a mobile device.

ENABLE BLUETOOTH

1. Quick press twice START/STOP to enable Bluetooth, and Bluetooth LCD symbol appears.
2. Device starts to advertise to be found, and to be connected. Device Name shown on TraceableGO™ App discovered list looks like CC653X-xxxx, where “CC653X” indicates model number and “-xxxx” is last 4 digits of device serial number.
3. If no connection has been made for MINUTU BAT, Bluetooth will be disabled to save battery life, and Bluetooth LCD symbol disappears, or quick press twice again to disable Bluetooth.

ERA VIEW PRE-CONFIGURED SETTINGS

1. Enable Bluetooth on device (see above).

2. Open TraceableGO™ or TraceableLIVE® App on any bluetooth enabled mobile device.
Oharra: Mobile device must have Bluetooth enabled to receive signal. To enable Bluetooth on a mobile device see mobile device settings.

3. Use TraceableGO™ or TraceableLIVE® App to connect to device. Once the app is open it will begin searching for devices to connect to.

A list of available Dataloggers will appear.

Oharra: TraceableGO Bluetooth Dataloggers are serialized and each logger name will match the sticker located on the side of the unit.

4. Once device is selected select Configure.

5. The following parameters are configured through App: START Mode, STOP Mode, ALARM Enable/Disable, Celsius/Fahrenheit, Memory Mode, Data Logging Interval, Alarm Setting.

6. TraceableGO™ comes pre-programmed. To view current settings, tap on configure once device is selected in App.

7. Device comes pre-configured as shown below:

a. Gailuaren izena
b. Gailuaren serie zenbakia
c. Current Battery Status
d. Current Temperature and/or Humidity Readings

PRE-CONFIGURED DEVICE SETTINGS

1. START Mode: Push Start
2. STOP Mode: Push Button Stop
3. Memory Mode: Wrap when Memory is Full
4. Unit Preferences: °C
5. Alarm Setting Alarm Low:
   TAP ON VALUE TO CHANGE
   ▪ Temperature: 2°C (6535 only)
   ▪ Temperature: 20°C (6537 only)
   ▪ Humidity: 25% RH (6537 only)
6. Alarm Setting High Alarm:
   TAP ON VALUE TO CHANGE
   ▪ Temperature: 8°C (6535 only)
   ▪ Temperature: 30°C (6537 only)
   ▪ Humidity: 75% RH (6537 only)
7. Alarm Enable/Disable: Enabled
8. Data Logging Interval: 5 minutes
9. Date/Time is also set to current to central time (Automatically updates when connected to mobile device).

Tap Configure to change factory settings

1. START Mode
Berehalako hasiera: Once device is configured it will begin Datalogging.
Sakatu botoia: Press START/STOP Button to begin Datalogging.
Atzeratua: Select number of Hours, Minutes and Seconds when device is to begin Datalogging.

2. STOP Mode
Inoiz ez: Device will never stop Datalogging.
Sakatu botoia: Sakatu HASI/GELDITU Button to Stop Datalogging.

3. Memoria modua
Wrap When Full: Once memory is full, oldest data points will be overwritten with new data points.
Stop When Full: Device will stop recording when Memory is Full 64K (65,536) data points, 7.5 months on 5-minute logging interval.

4. Unit Preferences
° F: Select Fahrenheit
°C: Select Celsius

5. Alarm Setting Alarm Low: TAP ON VALUE TO CHANGE

• Tenperatura: Set LOWEST Temperature before an alarm is triggered.
• Humidity (6537 only): Set LOWEST Relative Humidity before an alarm is triggered.

6. Alarm Setting High Alarm: TAP ON VALUE TO CHANGE

• Tenperatura: Set HIGHEST Temperature before an alarm is triggered.
• Humidity (6537 only): Set HIGHEST Relative Humidity value before an alarm is triggered.

7. Alarm Enable/Disable
Gaituta: Alarma aktibatuta dago.
Desgaituta: Alarma itzalita dago.

8. Data Logging Interval
Slide to desired Logging Interval.

9. Save Configurations: Uneko ezarpenak gordetzen ditu.
OHARRA: Saving a Configuration will delete all data on device.

Once device has been configured, device enters STANDBY Mode.

Date/Time is also set to current to central time (Automatically updates when connected to mobile Gailu).

HOW TO DOWNLOAD DATA TO MOBILE DEVICE

OHARRA: To download data either TraceableGO™ or TraceableLIVE Apps must be downloaded to a mobile device.

ENABLE BLUETOOTH

1. Quick press twice START/STOP to enable Bluetooth, and Bluetooth LCD symbol appears.
2. Device starts to advertise to be found, and to be connected. Device Name shown on TraceableGO™ App discovered list looks like CC653X-xxxx, where “CC653X” indicates model number and “-xxxx” is last 4 digits of device serial number.
3. If no connection has been made for MINUTU BAT, Bluetooth will be disabled to save battery life, and Bluetooth LCD symbol  disappears, or quick press twice again to disable Bluetooth.

TO DOWNLOAD RECORDED DATA

1. Device must be stopped. Enable Bluetooth on device (see above).

2. Open TraceableGO™ or TraceableLIVE® App on any bluetooth enabled mobile device. Oharra: Mobile device must have Bluetooth enabled to receive signal. To enable Bluetooth on a mobile device see mobile device settings.

3. Use TraceableGO™ or TraceableLIVE® App to connect to device. Once the app is open it will begin searching for devices to connect to.

A list of available Dataloggers will appear.

Oharra: TraceableGO™ Bluetooth Dataloggers are serialized and each logger name will match the sticker located on the side of the unit.

4. Once device is selected select Download Data.

5. App will begin extracting the data from TraceableGO™ Device.

6. Once data download is complete, mobile device will display options how to send PDF file, or CSV file (TraceableLIVE only). Tap Done and download is complete.

ZEHATZAK

Katua. 6535. zenbakia

Katua. 6538. zenbakia

Katua. 6537. zenbakia

TENPERATURA

6535: Ambient Range: -20.0 eta 70.0 °C artean (-4.0 eta 158.0 °F)
6536/6538 Probe Range: -50.0 eta 70.0 °C artean (-58.0 eta 158.0 °F)
6539 Probe Range: -90.00 eta 100.00 °C artean (-130.00 eta 212.00 °F)
Ebazpena: 0.1°C
Zehaztasuna:
6535: ±0.4°C between -10 and 70°C, otherwise ±0.5°C
6536/6538: ±0.3°C
6539: ±0.2°C

RELATIVE HUMIDITY & TEMPERATURE

Tenperatura-
Giro-barrutia: –20.0 eta 70.0 ° C (–4.0 eta 158.0 ° F)
Ebazpena: 0.1°C
Zehaztasuna: ±0.4°C between –10 and 70°C, otherwise ±0.5°C

Relative Humidity—
Giro-barrutia: 0% to 95%RH, non-condensing
Ebazpena: % 0.1 RH
Zehaztasuna: ±3% RH between 5 to 75%, otherwise ±5% RH

KANPOKO ZUNDA

6536 Bullet Probe: Standard plastic probe sensor with cable. Designed for use in air and liquids, the sensor and cable may be completely immersed. Probe size: 3/16” diameter, 4/5” length; 10 foot cable

6538 Bottle Probe: Designed to simulate the temperature of stored liquids, use in transportation coolers, refrigerators and freezers. Bottle probes are filled with a patented nontoxic glycol solution that is GRAS (Generally Recognized As Safe) by the FDA (Food and Drug Administration) eliminating concerns about incidental contact with food or drinking water. The included micro-thin probe cable permits refrigerator/freezer doors to close on it. (Do not immerse bottle probes in liquid). Probe size: 1 x 2-1/2 inches; 10 foot cable.

6539 Stainless-Steel/Platinum Probe: Detachable stainless steel 316 Probe with Platinum Sensor and 9 feet of cable are supplied with the unit. Probe has a diameter of 1/8-inch, stem length of 6-1/4 inches, overall length of 9 inches.

Bateria: 2 AAA Alkaline batteries (3.0V)

Dimentsioa: L x H x D: 3.5 x 2 x 0.79” (89 x 51 x 20 mm)

Bateria mailaren adierazlea:

Bateria maila	LCD symbol
≥ 80% (2.78V)
≥ 60% (2.56V), < 80%
≥ 40% (2.34V), < 60%
≥ 20% (2.12V), < 40%
≥ 10% (2.01V), < 20%
< 10% Flashing

Oharra: Battery level is updated every 5 minutes.

Oharra: Once battery level drops to below 10%, device may not work properly. Replace batteries immediately.

Oharra: When replacing batteries, after removing the old batteries, wait 10 seconds before inserting new batteries. Otherwise, Bluetooth may not work properly.

MEASUREMENT READING UPDATE FREQUENCY

Temperature and Humidity: 5 seconds;

Oharra: If a reading is out of operating range, corresponding location on LCD will display ‘–.-‘, and such out of range reading will not trigger alarm.

DATA LOGGING FREQUENCY:

5 min by default, user-adjustable between 1 minute and 12 hours with 1 minute step.

DATA STORAGE CAPACITY

Alarma: Most recent 90 Alarm events

Datuak: 64K (65536) data points, 7.5 months on 5-minute logging interval

DEVICE OPERATING MODES

• IDLE Mode: First time battery inserted, and device has not been configured
• STANDBY Mode: Device has been configured, but not started;
• RUN Mode: Device starts to measure and log data.
• STOP Mode: Device stops from RUN Mode. In STOP Mode, device does not update measurements or log data, and the last measurements are displayed.

VIEW GAURKO IRAKURKETA

1. Temperature ONLY unit: Current reading, minimum/maximum reading, run time/alarm time toggling, Memory mode are shown on LCD.
2. Humidity and Temperature unit: Current temperature/humidity reading toggling every 5 seconds, minimum/maximum reading since last clearing, run time/alarm time, Memory mode are shown on LCD.

VIEW CURRENT MIN/MAX

Temperature ONLY unit: Current temperature Min/Max values are displayed on LCD. Humidity and Temperature unit: Current temperature/humidity Min/Max values are toggled display.

Oharra: Every time device is configured, or resumes to run from STOP Mode, Min/Max values are reset.

VIEWING RUN TIME/ALARM TIME

Run Time/Alarm Time is toggled to display on LCD. If Run Time is displayed, LCD symbol KORRIKA DENBORA appears; if Alarm Time is displayed, LCD symbol ALARMA ORDUA agertzen da.

Oharra: Alarm Time is accumulated for both Low Alarm and Hi Alarm for each channel (temperature, humidity).

MEMORIA

If Memory Mode is set to WRAP WHEN FULL, appears on LCD; If Memory Mode is set to STOP WHEN FULL, MEM LCDan agertzen da.

ALARMA

1. Once an alarm is triggered by any of temperature, humidity out of set alarm range, LCD symbol LOW ALM eta/edo HI ALM starts to flash. An Alarm Event will be logged.
2. Sakatuz HASI/GELDITU once will clear alarm, LCD symbol stops flashing. An Alarm Acknowledge Event will be logged.
3. If temperature, or humidity falls back to normal range, an Alarm Event will be logged. If any of temperature, humidity measurement goes back to out of alarm range, alarm will be triggered again.
4. If device’s START Mode is configured as PUSH BUTTON TO START (default), device LCD displays ‘push to start’. Press and hold HASI/GELDITU until LCD symbol appears. Device enters RUN Mode. If device’s START Mode is configured as IMMEDIATE START, device enters RUN Mode immediately. If device’s START Mode is configured as DELAYED TIME START, delayed start time set by user is counting down on device LCD. Once the counting time reaches 0, device enters RUN Mode.
5. sartzen bada RUN modua, LCD symbol KORRIKA appears, and logs data at user-defined interval. If STOP Mode is configured as PUSH BUTTON TO STOP, press and hold HASI/GELDITU until LCD symbol GELDITU appears. Device enters STOP Mode. If STOP Mode is configured as NEVER STOP, device will ignore button press, and will stop when memory is full if Memory Mode is set to STOP WHEN FULL, or will stop when TraceableGO™ App is connected to device and downloads the data.
6. If in STOP Mode, press and hold HASI/GELDITU until LCD symbol KORRIKA appears. Device enters RUN Mode and resumes to log data at current setting. Anytime device resumes to log data from STOP Mode, Min/Max values are reset.

Oharra: If device in STOP Mode, START Mode will be set to PUSH BUTTON TO START regardless of previous Start Mode Setting. If Delayed Start Mode is needed while device in STOP Mode, device must be re-configured.

Oharra: While device is connected to TraceableGO™ App, once Device has received command from App to upload data to App, device will stop logging data and enter STOP Mode if it is still in RUN mode.

VIEW MEMORY USAGE, CURRENT DATE/TIME, DEVICE’S SERIAL NUMBER

1. Sakatu eta askatu HASI/GELDITU botoia

2. Memory usage in percentage is shown on LCD. The percentage indicates how much internal data memory storage has been used;

3. Number of days, hours, minutes left till memory is full are also displayed on the second line;

4. 10 segundo barru, sakatu HASI/GELDITU again, current date/time is displayed on device LCD. The following figure shows 9/14/2017, 17:30

5. 10 segundo barru, sakatu HASI/GELDITU again, device S/N will be displayed on LCD.

6. To return to normal working status, press HASI/GELDITU again, or wait for 10 seconds and device will automatically go back to normal working status.

Oharra: If Memory Mode is set to WRAP WHEN FULL: LCD symbol starts to flash on the display when the memory is full. Once memory is full, the oldest data points will be overwritten with new data points.

If Memory Mode is set to STOP WHEN FULL: LCD symbol MEM starts to flash on the display when the memory is 95% full. Once memory is full, the device will stop logging new data points.

CLEAR DATA MEMORY STORAGE

1. Data points stored in device internal storage can only be cleared through App or battery removal.
2. Each time device is configured, all stored data points will be cleared.
3. Run Time/Alarm Time are also reset.

ARAU-INFORMAZIOA

Ekipo hau probatu da eta B Klaseko gailu digital baten mugak betetzen dituela ikusi da, FCC Arauetako 15. zatiaren arabera. Muga hauek etxebizitza-instalazio batean interferentzia kaltegarrien aurka arrazoizko babesa emateko diseinatuta daude. Ekipo honek irrati-maiztasun-energia sortzen, erabiltzen eta igor dezake eta, argibideen arabera instalatu eta erabiltzen ez bada, interferentzia kaltegarriak sor ditzake irrati-komunikazioetan.

Dena den, ez dago bermatzen instalazio jakin batean interferentziarik gertatuko ez denik. Ekipo honek irrati- edo telebista-harreran interferentzia kaltegarriak eragiten baditu, eta hori ekipoa itzali eta piztuz jakin daiteke, erabiltzaileari gomendatzen zaio interferentziak zuzentzen saiatzea, neurri hauetako bat edo gehiago erabiliz:

• Berbideratu edo lekuz aldatu antena hartzailea.
• Handitu ekipoaren eta hargailuaren arteko bereizketa.
• Konektatu ekipoa hargailua konektatuta dagoen zirkuitu desberdineko entxufe batera.
• Kontsultatu banatzaileari edo irrati/telebistako teknikari esperientziadun bati laguntza lortzeko.

Gailu honek FCC Arauen 15. zatia betetzen du. Funtzionamendua bi baldintza hauen menpe dago: (1) gailu honek ez du interferentzia kaltegarririk eragin, eta (2) gailu honek jasotako edozein interferentzia onartu behar du, nahi ez den funtzionamendua eragin dezakeen interferentziak barne.

Hereby, Traceable Products, declares that this digital thermometer is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Gailu honek Industry Canada lizentziarik gabeko RSS estandarrak betetzen ditu. Funtzionamendua bi baldintza hauen menpe dago: (1) gailu honek ez du interferentziarik eragin, eta (2) gailu honek edozein interferentzia onartu behar du, gailuak nahi ez den funtzionamendua eragin dezakeen interferentziak barne.

OHARRA: BETETZAILEA EZ DA BETETZEKO ARDURADUNAK ERABILIZ ONARTZEN EZ DUEN ALDAKETA EDO ALDAKETAREN ARDURADUZ. ALDAKETAK ERABILTZAILEAREN EKIPOA ERABILTZEKO AGINTEA DENEZ IZANGO DIOTE.

BERMEA, ZERBITZUA EDO BIRKALIBRAZIOA

Berme, zerbitzu edo birkalibraziorako, jarri harremanetan:

TRACEABLE® PRODUKTUAK
12554 Old Galveston Rd. Suite B230 • Webster, Texas 77598 AEB
281 482-1714 telefonoa • Faxa 281 482-9448
Posta elektronikoa support@traceable.com • www.traceable.com

Traceable® produktuak DNV-k ISO 9001:2015 kalitate-ziurtagiria du eta A2LA-k ISO/IEC 17025:2017 kalibrazio-laborategi gisa akreditatuta.

TraceableLIVE® and TraceableGO™ are registered trademark/trademarks of Cole-Parmer.

©2020 Traceable® Products. 92-6535-20  Rev. 3 080725

Dokumentuak / Baliabideak

TRACEABLE CC653X Temperature Bluetooth Data Logger [pdfArgibideak CC653X, CC653X Temperature Bluetooth Data Logger, Temperature Bluetooth Data Logger, Bluetooth Data Logger, Data Logger

Erreferentziak

• Erabiltzailearen eskuliburua